Voro in the bathroom how to eliminate folk. How to read the blockage in the bathroom available to the means? Best specialized funds

Very often the owners fall the question "How to clean the drain hole in the bathroom from the hair?". Often the drain is clogged by hair. There are 2 solutions for such a problem: to understand why water does not go to the drain hole, or cause plumbing.

How to clean the drain hole

The reasons for which the blockage may appear in the drain hole of the lord. It can be clogged not only by hair, but also small litter, rollers from clothes, wool four-legged pets.
When all this accumulates in plum, the formation of a lump, which is the reason that the water does not leave. Moreover, this lump becomes more and more, begins to appear bad smell.
Well, proceed. In order to clean the drain hole, you should try the following ways:

• try to clean the block under the cap covering the drain hole. Even if it seems to you that the lid is clean, check anyway. It is very likely that you will find hair there in a huge amount. Plums, who have a cross plug, are most susceptible to such stamps. If you have a bathroom, in which the plug is installed, you will need to raise the plug before cleaning. The guide plate is unscrewed, and only then you can remove the plug.

If the face of the hair is deeper than you expected, you can take advantage of:

• wire hook.
  Take wire shoulders, spit and bend into hooks. Place the hook in the drain hole and pull the blockage. IMPORTANT: you need to pull out, and not to suck the litter. Otherwise, you will definitely have to cause plumbing.
• vanutuz.
  Probably the most common method. But it will only help if the block is small.
  Vanatuz should be the size as a drain hole. Clean the drain hole with a cantuza is easy, so if you are often clogged with plums, it will become an indispensable assistant to you. How to break through the drain hole with a vacuum? Take the plug and close the drain, lubricate the vaseline and press the drain hole. Make about 10 sharp reciprocating movements. If the water is still "worth", add hot water. Type so much in the bathroom so that it covers the half of the vehicle. Subsequent actions are the same as described above: trying to "break through" a blockage.
• cable. The power can help with serious sewage stamps. The cable is a twisted wire, at the end of which there is a handle (it can be wooden or plastic)
  Plus this device is that it can cope with a blockage, which is at a depth of 9 meters.
  How to use a cable? Take the pen and insert the cable into the drain, hold one hand and scroll the cable, the other - push it deeper into the drain hole. Now you can find roses on which there are interconnected hooks that help get rid of hair in the drain hole. If you felt, That the cable burst into something, "stalled" - know that this is the location of the cloud. Now you need to repeat the movements back and forth several times and then you can clean the drain hole. You can then pull the cable.
• scotch tape. To break through the drain hole, you can use any sticky tape. Cut the strip of approximately 50 cm. Place the tape into the drain hole and take over the inner walls. Almost all hair remains on Scotch. When pulling out a sticky tape with hair, do not forget to wash off the remains of the cloud.
• chemical preparations. In the fight against clouds you can use household chemicals. Ask the store's seller so that he suggests which means is better.

before applying chemical preparations for cleaning the drain hole, read the instructions and the composition of the drug. Why? Some drugs are not suitable for all types of pipes. So, "Mole", which is considered very effective toolYou can not clean stools in plastic pipes.
Using household chemicals to combat clouds, you need to clearly follow the instructions, otherwise it will not be any sense. The drug needs to fill or fall asleep into the drain hole and leave for a certain period of time (specified on the package). Then you just need to wash the remedy.

If you do not comply with the rules of use, there is a risk of pipe deforming, or ineffective use of the means. Do not forget to put on gloves when you clean the drain. Safety - above all.

Top Products for Cleaning Drain Hole

How to clean the siphon in the bathroom.

Sometimes the problem lies not in the drain hole, but deeper - in the siphon. How to clean the siphon yourself?

• on the floor under the siphon should be rag
• under the siphon put a small pelvis.
  Perhaps one cloth is not every rag, and since the water in the clutched siphone is rather dying, it is better to substitute the basin, so that then not to wash the whole bathroom and do not get dirty yourself.
• then cautiously unscrewed the shutter nut
• removed flask
• after you remove the flask, the water flows into the pelvis ..
• then remove the siphon and rinse it under flowing water. The water pressure will help you get rid of small pieces of blockage, wool, hair, which remained on the walls of the siphon.
• finish everything back. Important: The nozzle that is responsible for the drain should not be resting in the flask.
• after the siphon in place, you need to check whether the connection is tightly and does the siphon flow.

What to do so that the drain hole does not clog

After reading the article, you probably understood that it was not so difficult to clean the drain hole and siphon. But in order not to spend time on the cleaning procedure regularly, you need to adhere to certain rules, the prevention of blockage of the drain hole is important.

• set into the drain hole, the grid that will delay Sorrow
• from time to time, brush the drain hole with the help of household chemicals.
• once every three months clean the siphon

If you follow these simple rules, you will never need to search for you on the Internet "How to Clean the drain hole in the bathroom from the hair"!

Video about how to eliminate zoom

None of us is immune from such an unpleasant situation as zoom in sewer pipeoh. A similar problem may occur at any point of water supply, whether it is a bath, kitchen sink, washing or toilet. To prevent such trouble, it is necessary to regularly carry out preventive measures, and also clearly submit, because of what the blockages may arise. Today we will analyze the situation when the bath was clogged, what to do in this case, and with what means and methods to eliminate the problem.

The reasons for the occurrence of a bedroom in the bathroom

Whatever careful in the use of plumbing was neither the owners of the apartment, sooner or later the question arises before each family: "What to do if the bath clogged?". Zavor in the bathroom is unpleasant not only by the fact that water ceases to go into the drain, but it is also added to the unpleasant smell. In addition, the plumbing coating begins from the dirty water, and the desire to swim in such a bath disappears immediately.

The flow can be clogged for various reasons, because to track that it falls into the drain hole is extremely difficult. It can be hair, and animal wool, rollers from clothes and other small garbage. All this is assembled in the pipe and forms a dense lump, which prevents the free passage of water.

Important! First, the water begins to pass slowly through the drain, and then the flow can stop completely.

In addition to violating the conditions of operation of plumbing, the following problems include the reasons for the formation of blocks:

• Errors when installing sewer pipes. Incorrect tilt of pipes can cause a problem.
• Falling into the draining of foreign objects.
• The formation of pollution on the interior walls of plumbing.
• Problems with central sewers. In multi-storey houses, general barns associated with the problems of central sewage are very often arising. To determine this type of blockage, simultaneously turn on the water in the bathroom and in the kitchen. If the shaver is common, the water will not go into the sink or in the bathroom.

Important! Solve the provision of central sewer should manage a management company or an organization responsible for your home.

If the problem with the sewage is only in your apartment, then proceed to the elimination of the bedroom in the bathroom using mechanical or chemical methods that will be discussed on.

Elimination of the bathroom

There are a lot of options for solving a bad passage of water in the pipes. First you need to decide how serious the problem arose:

• if water does not leave at all, then it is a serious blockage;
• if the water simply flows very slowly, this is an easy problem that can be solved by spending the minimum of forces and means.

Important! Of course, there may be exceptions to the rules when, it would seem, a serious problem is solved by the easiest way - with the help of several manipulations with Vanatuz.

All methods of elimination of blockages are divided into two types:

1. Mechanical. This method involves the use of tools such as:
   1. Vanutuz.
   2. Sanitary cable.
2. Chemical. To solve the problem use household chemicals.

All these methods are able to eliminate the block in the bathroom without attracting specialists. Use these methods and tools can anyone - from a healthy middle-aged man to fragile young girl. The most important thing is to choose the method correctly for your situation to save time and means, and get the best result.

Mechanical ways to combat clouds

When a small blockage occurs, or in the case when it originated for the first time, apply the simplest methods: use of a cantuza or solve the problem with the help of folk remedies, if possible - with the help of household chemicals.

Consider how to use these means when solving the problem.

Cleaning vests

In every house, for sure, there will be this indispensable thing. Most often, Vatuzi is used to eliminate blocks in the sink, but if the problem occurs near the drain hole of the bathroom, then use this simple device to solve the problem.

Procedure Next:

1. Before cleaning, fill the bath with a small amount of water.
2. Install the vehicle on the drain hole in such a way that the rubber part of the device completely blocked the stock.
3. The second drain hole located on the vertical part of the plumbing (under the crane), close the plug. Thus, you do not allow water and garbage to get into the second drain.
4. Vanza handle alternately lifted up and lower down. Air, falling into the drain hole, the resulting blockage is pushed.
5. Remove plum tubes.
6. Turn hot water to wash off all pollution.
7. If the first attempt was not able to remove the blockage, then repeat the procedure several times.

Important! Applying a cantuz to clear the bedroom in the bathroom, it is important to know the following nuances:

• Cleaning the bathroom on the "dry", without water, will not be effective enough. The flow of water is better pushing the garbage than just air.
• Use vanatus in preventive purposes regularly - then you will not come across the problem of poor water.
• If, as a result of the troubleshooting of the problem, the garbage began to appear from the drain, then collect it and throw it away, and do not try to return the debris back into the drain.
• Instead of cork to create tightness, you can use the second vanatoux, but in this case you will need help another person.

Purchase of sanitary cable

Plumbing cable is a pretty thick twisted wire, rolled into a small spiral. At the end of the cable, for convenience, a handle with a plastic or wooden nozzle is provided.

Important! The usual cable length is 2.5-3 m. The appointment of the device is to hook a garbage lump and pull it onto the surface or push the lump further into a wide part of the sewage.

Conduct work with the device is better together.

Important! It is necessary to use a sanitary cable in the case when the blockage is far away in the pipe or lump of garbage is strongly pressed and can not solve this problem.

Procedure for cleaning:

1. The end of the cable gently insert into the hole for the drain, and better - immediately into the tap of the pipe.
2. One person turns the cable, performing rotational movements, and the second - pushes the device forward.
3. The cable spinning decides at once two tasks at once: turns turns the pipe, and the sharp ending removes the accumulated garbage. Therefore, make sure that the cable is constantly tightened, otherwise it may be damaged and it will not be used in the future.
4. As soon as the cable movement will become freer, make some sharp movements there and to finally make sure the problem is eliminated.
5. Pull the cable and rinse it carefully.
6. Turn on hot water and wash all the remnants of dirt.

Important! If, when solving the question, the bath was clogged - what to do, you preferred a plumbing cable, take such useful tips on the note:

• Plumbing cable can be purchased in a shopping store or make it yourself. For the manufacture of the device, any durable and flexible wire will suit one end of the wire and give it a rounded shape, the second - wrap with rubber or rigid cloth so that the handle turned out.
• Do not use the cable when cleaning chrome and plastic pipesSince the device can damage the inner surface of the pipes.

Chemical method of cleaning

Quickly and easily can be eliminated in the bathroom with various chemicals. This method has long been used for a long time, just used to clean the plumbing folk remedies, and now the more advanced compositions of household chemicals. Purchase household chemicals that are able to solve the problem of water stagnation in sewage literally in a few minutes, you can in any economic store or supermarket.

Important! Especially effective, such funds cope with pollution of organic origin, which accumulate on the walls of pipes and gradually reduce their diameter.

Household chemicals are produced in the form of powders, liquids or gels. Among the entire variety of compositions, choose those in the instructions of which it is indicated that they dissolve the hair and animal wool. Also, pay attention to which pipes are intended for the drug.

Important! For the bathroom, select a means capable of dissolving the hair, and for kitchen sink - a drug that can dissolve fat.

The most popular following chemicals:

• "Mole". This is one of the most effective means. By virtue of the aggressive medium, this drug is not recommended for plastic pipes.
• "Mister Muscle". This drug is perfect for all pipes. The composition is produced in the form of gel and foam. The drug effectively purifies the surface, destroys unpleasant odors, bacteria.
• "Potechan." The tool quickly dissolves any contamination, even the strongest breakdowns in the bathroom. The only minus is a sharp smell.
• "Tiret". The drug perfectly copes with complex problem problems, but unlike other means, does not have a sharp smell of ammonia.

Important! Using chemicals, do not forget that frequent use of their use leads to the destruction of the inner surface of the pipes and gradually wear them.

If the bath clogged, then use chemicals as follows:

1. Read the instructions to figure out how to use the preparation acquired and make sure that the tool is suitable for your type of pipes.
2. Purify (fill) the remedy into the drain hole. If it is powder, then it must be pouring it a glass hot water.
3. Wait for some time - indicated in the instructions.
4. Open hot water, remove all the remnants of garbage and dirt.

Important! Using chemicals to clean the blocks, remember the safety technique: secure yourself with rubber gloves, protective glasses and adhesive apron.

Folk remedies in the fight against clouds

Today, households do not resort to folk remedies often, but not always at hand chemicals, and home products do not work worse with problems. We offer you the following folk recipes.

Brought up the bath - what to do? Folk remedies

The simplest and affordable means is the usual boiling water. However, it is better suitable for the sink in the kitchen, as fat dissolves well. And with serious problems, soda and vinegar will cope.

The cleaning procedure is as follows:

1. Put a glass of soda into the drain hole.
2. Fill over soda one glass of vinegar (not essence).
3. Close the hole with a plug so as not to prevent the chemical reaction.
4. In 25-30 minutes well rinse the sewer stock hot water.

Important! Folk remedies Capable and prevent blockage, and remove it, even if you take them in other combinations:

• Soda and vinegar use in order to prevent the formation of blockages.
• You can apply and soda without vinegar - pour half a pack in stock, and after 5 minutes turn on hot water.
• You can use lemon juice for cleanings - pour juice 2-3 lemons into the drain hole and leave for an hour. After cleaning, wash the remedy with plenty of hot water.

Cleaning siphon

Siphon cleaning allows you to get rid of garbage accumulated in pipes and unpleasant odorAfter all, on the walls of the siphon eventually formed a malware precipitate.

Important! Depending on the intensity of the use of the bathroom, the siphon must be cleaned at least once every two months, but it is possible and more often.

Siphon cleaning procedure:

1. Located on the floor under the siphon fabric capable of absorbing moisture.
2. Put the basin on the cloth. These events will prevent the ingress of dirty water to the floor and will reduce cleaning time.
3. Carefully unscrew the shutter nut and remove the flask.
4. Sale dirty water, remove the fine garbage.
5. Rinse your siphon thoroughly, remove the entire plaque from the walls.
6. Install the siphon in place. Make sure the running pipe does not relieve on the flask, otherwise it will be disturbed by the hydroplays.
7. Check the tightness of all connections - to do this, open the faucet and fill the hydraulic table.

Preventive actions

The problem is always easier to prevent than to solve. Therefore, in order not to decide how to eliminate the zoom in the bathroom, follow the following recommendations:

• At the drain hole, be sure to install a protective mesh. This will help protect the drain from wool, hair and small garbage.
• Periodically spend the purification of pipes by folk or chemicals. The main thing is not to overdo it and do not damage the pipe.
• Watch that household waste, garbage and rags do not fall into the drain.
• To prevent fat accumulation on the walls of the pipes, periodically rinse the sewer system with hot water for 10 minutes.
• Conduct the prophylactic cleaning of the siphon at least once a month.
• Use for prevention of vanatuz.

Stock foot

We hope that the information outlined, helped you solve the problem of the bedroom in the bathroom. But it will be much better if the sewer pipe will never be clogged - it will happen if you take measures in advance to avoid such troubles. Regularly spend gentle preventive measures, then expensive chemicals you will not need, and the bath will always be filled with clean water and fresh smell.

Drain in the bathroom can clog at any time, and such a nuisance always inevitably leads to several problems at once.

1. An unpleasant smell appears, which can be felt not only in the same room, but also spread throughout the apartment or house.
2. The impossibility of plum leads to the fact that it is impossible to wash.
3. This situation is dangerous flooding. This may happen if the problem is not detected in time.

Council: at the first "symptoms" of the appearance of the zero, you need to react immediately. This trouble is resolved much easier at the very first stages.

It is not necessary to hope that garbage quickly and will leave the pipe with himself. If the water does not go into the drain hole, then the sewer has to be cleaned using special means and folk Methods. What to do if there was a blockage in the bathroom, how to eliminate it yourself - you can learn about it below.

Why appears blockage in the bathroom and how to avoid it

It is not always possible to follow, so that in the drain, it is not carved small foreign bodies various origin. There may be:

• animal wool when washing them;
• hair;
• sand and crushed shells (when taking a shower immediately after the beach);
• fat droplets, etc.

Also a considerable role is played by wear of pipes, on the inner walls of which a layer of fatty and lime depositsas well as rust.
And if in the first case you can still use a special mesh and partially remove the garbage from the bottom of the bath, without giving it to "leave" in the drain, then only the adoption of preventive measures can minimize the formation of the wave.

The first way. In the fight against fat deposits, the systematic cleaning of communications is a strong head of hot water.

The second way.

1. Fall over a stack of soda into a drain hole.
2. Add the same amount of vinegar.
3. Tightly shut the flow of a cork or a conventional cloth so that the foam does not fall back (it is formed due to the starting chemical reaction).
4. Wait 2 hours.
5. Remove the damper and rinse pipes with hot hot water.

Also, the proven "people's" methods of preventing blocks include the use of citric acid - 2.5 full tablespoons of powder need to fall asleep into the drain and pour boiling water liter. Limonon will help dissolve lime raids on pipes and increase their inner diameter for easy efforts. it effective methodsHow to clean the blockage in the bathroom at home with the help of ordinary household funds. Below you can get acquainted with detailed instructionsWhat to do in each case.

How to clean pipes at home

Vantuz - special tool In the farm, which is used when clogging engineering communications. If the sewage system has been scored, it is important to remember the basic rules for using this device.

1. Near the drain hole, it is necessary to leave a small amount of water.
2. Tightly press the vanatuz to the surface of the bath at the place of the drain. It is necessary to ensure that the air does not fall under the rubber bowl.
3. Run a few energetic movements up-down with a wooden handle, and then remove the tool with a jerk.
4. If the result is not obvious, and water does not go out, the procedure is reproduced.
5. When everything works out, open a crane with hot water and rinse the pipes.

We need to use vehicles regularly in preventive purposes. Often the repeated process of pushing the small lumps of dirt, which is already inside, will prevent their accumulation into more volumetric masses.

Caution: manual acrylic baths Does not allow the use of this submitted means, as the tightness of the drain can be disturbed.

Another mechanical device that allows you to remove the accumulated garbage from the pipe is a plumbing cable.

1. To successfully eliminate the block, you need to insert a rope into a drain hole and start promoting it forward up to contact with a problem area of \u200b\u200bsewage.
2. The purpose of further actions is the destruction of "traffic jams" or its "drawing" and extracting to the surface. To do this, it is necessary to break through the obstacle, making reciprocating cable movements and at the same time rotating it around its axis (such a combination of receptions is possible using a special handle).
3. At the same time, hot water influxed into the hole will speed up the process of removing the blockage.
4. If the sensations of the cable movement inside are becoming more free, it is necessary, not in a hurry, remove the rope from the pipe and check whether it was possible to do what was thinking: whether water was merged now.

Important: When purchasing a device, it is necessary to consider the diameter of its transverse cut. The thickness of flexible cables offered today on the market varies from 6 to 28 mm. Too thin ropes are not effective to eliminate large blockages, and thicker and, accordingly, massive, can damage small pipes.

How to eliminate the blocks from the hair

To clean the sewage from the hair that fell into her, you can use both vanatuz and cable. But considering that these methods require the cost of time and application physical strengthIt is sometimes more convenient to refer to chemicals like Mole powder.

The active ingredients of such mixtures easily dissolve hair, wool and other small garbage. To use them in the standard case, you need to pour or pour the chemistry portion in the stock hole. After a while, prescribed in the instructions, rinse the pipe with a large amount of cold or hot water (depending on the selected reagent).

Council: The main condition for the safe use of such components is the protection of your hands from the chemical to them. Work in gloves.

If the block is at a small depth, you can apply a mini-cable in the form of a crochet wire at the end. Having dropped it into the drain, draw and remove a significant amount of hair stuck on the surface.

In addition to the described mechanical and chemical methods to eliminate this type of block, sometimes resort to "folk". You can use a conventional tape strip of about half a meter. The sticky tape is lowered into the drain, and part of the garbage is glued to it, and then removed. So you can act until the "plug" is completely removed. After that, the pipe is washed with water.

The best tool for cleaning pipes

Choice better remedy Upon elimination of internal pollution of pipes is ambiguous. Often, every mistress allocates one or a few most effective methods And inhibits its own home arsenal.

Factors that influence the choice of the procedure for cleaning pipes:

• availability of free time and the necessary tool;
• urgency problem solving;
• the degree of "nestness" of the situation;
• personal prejudices (for example, some people fear the effects of self-purification using chemicals).

In each case, it is reasonable to apply one or another tool. When using "chemistry", it is important to carefully read the labels to the means, as some of them can damage the material of sewer pipes - for example, deform plastic or "Corporate" cast iron. It should also strictly adhere to the time of the action of these substances, do not forget to wash them off when required by the instructions.

Do not and too "get involved" people's methodswithout trying their action gradually. For example, an effective means that purifies the tubes from blockages is perhydrol - a concentrated solution of hydrogen peroxide. But when interacting with the "Organic" contamination, such a substance gives a strong reaction. Therefore, it is necessary to pour it very carefully, small portions (since half a glass), withsting intervals. When forming too much foam, it is possible to neutralize it with water.

If your own attempts to solve the problem were not crowned with success, trust this question to professionals. Appeal to the specialized service and will become the most effective means to eliminate any traffic jam inside the pipe.

How to clean the drain in the sink in the bathroom

The most common problem if the outflow of water in the sink is slowed, is to clog the siphon under it. The pipe in this place is bent in such a way that any garbage is easily delayed there, and the flow can be clogged.

There are no restrictions on the choice of the problem of overcoming the problem. You can use chemical solvent compositions, or try to push the plug by Vatuz.

If you clean the pipe in this way failed optimal decision It will disassemble the siphon himself and eliminate dirt itself. Moreover, under the sink it is quite convenient to do.

Council: Before cleaning the pipes, stock bucket or basin. So it turns out to avoid the spread of dirt on the surfaces in the bathroom.

1. We substitute the dishes for flowing contaminants directly under the sink.
2. Separate the siphon from the pipe. We merge the water in a bucket or pelvis.
3. From the inside, carefully clean communication from dirt, remove the hair, the remains of food and other waste.
4. We process the inner surfaces by a degreasing agent and rinse with hot water.
5. Install the siphon in place. Turn on the water and check whether the problem is eliminated.

Such an unpleasant phenomenon, as a pipe zago, can be quickly eliminated. For this, it is not always necessary to disassemble the siphons or wait for the coming of a professional plumbing with special equipment. Most often, the possession of basic knowledge and elementary devices will help independently solve the problem and force the water to raise freely when it is necessary. We hope our advice with video will help you in overcoming these problems.

As a result of design errors, installation, operation of the sewer system, the user often needs to be eliminated in the bathroom at home own forces. This uses a chemical, mechanical or hydrodynamic cleaning method. Plumbing devices are additionally equipped with special devices - siphons, in pipes, risers are mounted fittings - revisions.

Sewage system B. country house And the apartment is designed together with the water supply. Two or three rooms with these engineering systems - Separate / combined bathroom and kitchen have general System Water supply and drainage.

Typical seasalization scheme in the apartment.

Lamb can be formed due to improper operation of any of the plumbing devices. There are several categories for the occurrence of sewage blockages:

In the kitchen, the nutritional waste of small, large fractions inevitably fall into the drainage system. This point of water intake is usually most removed from the sewage riser located in the toilet. With low volumes of water and corners of the slope of horizontal sections of the internal sewage, the liquid does not have time to carry out these waste in the riser.

The capacity is accumulated in the pipes, up to a block, which will have to be cleaned by the user. In addition, the organic begins to be processed by bacteria. The obstruction of the pipes may occur on any plot between the riser and the connection site of the kitchen sink. As a result, the performance of any plumbing device in the kitchen, combined bathroom, bath or toilet can be disturbed if the kitchen sink is connected to the sewage before the bathroom.

Cleaning methods

Due to the operational characteristics, the drainage system under the bath or in the shower cabin is most often clogged with long hair, which does not eradicate, even concentrated acid. Hair lumps accumulate in a siphon or an exhaust pipe after it. Siphon Plumbing Device Created to solve several tasks:

The design of the siphones allows you to create in front of the plumbing device the waterproofing - a fluid pillar, impenetrable for sewage gases, but at the same time makes it difficult to clean.

Start getting rid of the bar need from the most simple ways, then move to more complex if the previous one did not give the result.

Hydrodynamic

Vantuz

The simplest method of hydrodynamic washing is vanatuz, it helps to cope with clouds in 95% of cases:

• in the bowl of the plumbing device, we recruit water, about the middle of the pear of the vehicle;
• tool Install over the drain hole shower pallet, sinks or baths;
• plug by a wet rag and press the overflow hole with hand;
• a sharp movement down pressure on the handle of the vehicle, then as sharply pull up and so a few dozen times;
• water along with air, inside the rubber plate of the instrument, perform a hydraulic blow, which breaks through the plug.

It is necessary to hermeticly close the overflow hole of the bath or sink, otherwise it will not be possible to create a hydrate, the air will simply be released through the hole.

The previous method will help if the blockage is located to a bathroom / sink junction with a common pipe, as shown in the figure above. If the block is located after connecting two devices (see Figure below), in this case you need to close the overflowing holes and the bathroom and the sink at the same time, as well as the drain hole of the sink or bathroom, or work with two vessels at once. To do this, you will need an assistant.

Evidence that the block is located below the sink and the bathroom, is the frightening of water in the sinkon of the sink, when working in a bathroom.

There are three types of vanza to solve various tasks that differ in design:

• standard - rubber suction cup in the form of a bowl;
• toiletical - at the bottom of the suction cup is narrowed;
• piston - large-sized hand pump With a rubber cuff under the diameter of the plumbing plumbing hole.

A vacuum cleaner

If you have a washing vacuum cleaner, but there is no vanza, you can try to break through the plug them, but the kit must have a special nozzle. The vacuum cleaner is mounted on blowing.

The main complexity consists in sealing the connection site of the household electrical appliance hose with the sewer pipe. For this, a rubber coupling is used, a sleeve, a suitable hose.

High pressure devices

For hydrodynamic flushing of pipes of drainage systems, a high pressure apparatus is used, a special hose tip:

• one jet is directed forward strictly in the center of the nozzle, blurs the blockage high pressure water;
• several jets of a spherical head beat in reverse side At an angle of 30 - 45 degrees, cleaning the walls of the pipe from dirt behind themselves.

The operation is very dirty, therefore it is used only for systems of outer, storm, drainage sewage and pipes of roofing drain, flushing of standing of multi-storey buildings, which are difficult or cannot be disassembled for other cleaning technologies. Inside apartments and houses are not applicable.

Mechanical

Hooks, devices

Often, the siphon in the bathroom is clogged with long hair, you can try to get a bunch of hair without disassembled the siphon, with the help of remedies or special devices.

The hair is extracted with tweezers, nippers, wire crochet.

Industry produces several types of special devices:

Disassembly of siphon

If you can remove the zoom by the previous way, you can disassemble the siphon and rinse it manually, this is done as follows:

The cable must be pushing forward at the same time turn it into any comfortable side, rotation allows you to wind the hair accumulated in the pipe. After cleaning the cable and assembly of the siphon, you need to knock off the remnants of the dirt using a vanza.

Cable

Strong deep blockages and "overgrown" pipes that could not be pounding with vanatuz, eliminate with the help of special plumbing cables, they are both manual and in the form of a screwdriver or drill.

The algorithm of action to eliminate the zero inside the drainage system with a cable as follows:

The method is considered the most effective, however, has a serious minus - if the pipe is clogged with a plug from a viscous substance, the diameter of the hole in the zado will be slightly more cable thickness. Over time, you have to repeat the operation.

Industry produces plumbing cables of different lengths, diameter with several types of tips.

Chemical

All modern means for chemical cleaning internal sewage are divided according to:

• aggregate condition - powder, liquid;
• chemical composition is acidic, alkaline.

Acid preparations are available as a powder or granules are used in one reception. They destroy the hair, the organic, but not able to cope with fats, soap-sized, oils.

The alkaline means, on the contrary, neutralizes, dissolves soap films, oil, fat, but powerless to lumps of wool, hair. Mix acid with alkali is meaningless, because the result will be water with precipitated salts, according to the laws of chemistry.

Therefore, universal funds do not exist, the following algorithm of action is used:

• from the kitchen in the drain, few and fat usually fall, the recipes of drugs with alkali are more efficient;
• hair, animal wool is more often accumulated in pipes after plumbing installed in the bathrooms, acidic products are used here.

When mixing with water, the chlorine-containing agent of thyret forms acid, decomposing the organic and hair.

The M Mole includes caustic soda, when mixed with water, it is formed alkali, it allocated a large number of Heat. This allows you to wash off the fats, oil films from the inner surfaces of the pipes, destroying blockages from these materials. In addition, the caustic natra destroys the organic, paper.

Nevertheless, with all the relics of modern chemistry, these funds are ineffective, for the reason that they weakly interact with the place of the ground or outflow on the pipes themselves, they quickly flow into the sewer. In order to create a significant concentration, you need to pour these tools by liters through each hour within a day, which is very expensive. The chemical means are expressing greater efficacy in the siphons, but the design of the siphons is collapsible, therefore it is easier and cheaper to eliminate the zoom by the methods described above.

Folk

Under the people's liquidation, there are exclusively chemical recipes for funds, with which you can destroy the cork formed in the pipe. Initially used a mixture of soda with vinegar. However, the following nuances are characterized for this method:

• soda is food (NaHCO3) and caustic (NaOH);
• food soda reacts with diluted acetic acid with highlighting carbon dioxide CO2, H2O water and sodium acetate CH3Coona without heat;
• caustic soda - caustic soda - in itself is strong chemically active substancedissolving the organic, it does not need to be mixed with vinegar.

In stores, caustic natra is not for sale, because it is stored and used according to a special regulation. That substance is not a girlfriend.

The shedding of sewage boiling water also does not bring a tangible effect - the pipes and remaining stocks are heated at first. When the zero is reached, the water temperature reaches no more than + 50 ° C, which does not contribute to softening and washing the fats due to which it arose.

Folk methods, as well as chemical, not too effective, but not so beaten on the wallet.

Couple words about shower pallets

The main problems of operation of the shower cabin are:

• frequent location of the drain hole near the wall;
• lack of access to the internal sewage tee;
• capital sealing of the pallet without disassembly (especially self-made).

Because of this, access to the siphon is closed, it is impossible to disassemble it. Therefore, it is desirable to use special shower lads, in which the inner filling is removable, which opens access to the pipe and can be cleaned with a cable.

Collapsible shower ladder.

Prevention blocks

In the manufacture of the internal sewage project, it is enough to perform 7 conditions:

• continuous uniform slope 1.5 cm per 1 raman meter sewage from the farthest plumbing device to the riser;
• the location of the horizontal pipes of horizontal pipes towards the flow (assembly from the riser), the exception is coupling with double-sided terminats;
• diameter of pipes or corrugations from 40 mm for baths, sinks, shower cabins, shells, bidets, from 110 mm for toilet bowls, from 50 mm for horizontal sewage sites;
• connecting plumbing with oblique tees with a slope of the upper pipe along the flow of stock;
• the presence of revisions for cleaning;
• using siphones under each plumbing device with the exception of toilet bowls, shower cabins.

When operating, it is necessary to ensure compliance with the requirements:

During installation, it is necessary to withstand the bias of horizontal sections, use brackets that prevent pipes from sagging. In the bathrooms of buildings operated seasonally, temporarily, it is better to use dry hydraulic machines, as the liquid in standard siphons can be reduced with rare use.

Thus, it is possible to eliminate the internal sewage zoom in several ways. In most cases, Vanutuz or hook will help you, in the rest - the cable. Other methods are weakly effective.

Tip! If you need a bathroom repair masters, there is a very convenient service for the selection of specialists from. Just fill in the details of the order, the masters themselves will respond and you can choose who to cooperate with. Each specialist in the system has a rating, reviews and examples of work, which will help with the choice. Looks like a mini tender. The placement of the application is free and does not oblige anything. It works in almost all cities of Russia.

If you are a master, then go to, register in the system and you can receive orders.

Lambors are a common problem with which a person living in an apartment or country house may be faced. As a rule, they arise suddenly, while not always the opportunity or time in order to cause a specialist. In this case, you need to know how to clear the block in the bathroom at home.

It should be remembered that it is necessary to get rid of the problem even with the slightest water. If you run this moment, there will be much more time and effort to eliminate the consequences. To understand what is better to clean the blocking in the bathroom, you need to know its size, localization and composition.

The occurrence of blockages is determined by violations of the rules for the use of sewage. Cut pipes may be due to the following factors:

• Incorrectly specified angle of slope of the sewer pipe during its installation.
• Seen in the trumpet of garbage and hair.
• Total wear of the sewer system.
• The appearance of bodybaque.

Depending on the sewage point, the blocks will differ. So, in the case of the kitchen sink, the cause of congestion, as a rule, are the remains of food and oil, drowning with water through the drain grille. Food settles in a siphon flask, and fat can accumulate on pipes, especially intensively if the inner surface of their surface for some reason has lost its smooth surface.

The toilet is clogged due to the draining of solid garbage - vegetable cleaning, randomly washed rag. IN apartment houses Vomor may occur on the total sewage drain due to its large garbage tray. In this case, the malfunction is not eliminated on its own due to the lack of required tool and the audit window of the pipe in the apartment. Drain of the bathroom is clogged in the process of adopting hygienic procedures. Knowing the ways to clean the blocks, you can cope with them yourself without referring to the masters.

Disassembly of siphon

The main reason for the occurrence of tubes in the bathroom is hair and animal wool. First, the garbage is delayed on the drain lattice, but if it is not possible to remove it in a timely manner, it will drag on it with water and get stuck in it. In addition, during the taking of the soul you can drop various minor items, such as servants and rings. Initially, everything falls into the siphon, which performs two functions: does not smell from the sewage to fall into the apartment and protects the pipes from the garbage from entering them.

If the water in the bathroom begins to leave poorly, and with visual inspection of plum in the siphon, dirt and hair are visible, then this device can be disassembled to extract garbage from it. This requires special plumbing knowledge and equipment.

Before the start of dismantling a siphon, a fabric is well absorbed under it, and when disassembling the sinks of the sink, you can put a bucket or pelvis under it. It is necessary in order to the water flowing during disassembly, often dirty, did not fall on the floor. The order of disassembly will be as follows:

• A plastic nut, which is located near the drain from the inside is unscrewed.
• Disconnect the flask and merge water from it.
• Next, the bottom of the siphon should be replenged and clean from the garbage, after which the flask is washed with water.
• The assembly is made in the reverse order, after which it is necessary to submit water to identify possible leaks and verification checks.

Application of chemistry

Many chemicals are produced to eliminate blockages. The components included in their composition make it possible to effectively destroy blockages of organic origin, for example fat deposits. Available such means both in the form of powders and in the form of liquids.

When they are used, it is important to withstand the time indicated by the manufacturer. Discharge funds are not recommended, since not all materials of sewer pipes are resistant to aggressive chemical components.

The liquid compositions simply pour into the hole of the drain and wait for the specified time. Powders fall asleep in the drain and poured a small portion of water. Upon completion of the required temporary pause, the system is washed with hot water.

The most common chemical preparations with a good reputation are considered:

• Mister Muscle. In addition to means for washing floors, the manufacturer releases drugs to eliminate blockages. It is a gelling agent, in addition to breaking the blocks, has antibacterial properties.
• Mole. Liquid concentrate of hydroxy and acetic acid mixture. Produced in the form of a gel. Due to the presence of aggressive chemical components, its use is extremely not desirable in pipes that are susceptible to the composition of the funds.
• Tiret. This agent is suitable for any material of sewer pipes, since it does not in its composition of aggressive chemicals.
• Flup. Powdered means for removing the climb and fat congestion.

In addition to specialized funds, the elimination of organic blockages are well coped with substances that can be found in almost every apartment: acetic acid and a calcined soda. Entering the reaction with each other, they form a large amount of carbon dioxide, which pushes the jam. In addition, acid additionally corrupt fat deposits. In order to clean the block in the bath in this way, you must do the following:

1. In the hole of the plum fall asleep half of the pack of soda.
2. After 15 minutes, the half-table of vinegar is poured and the plum is closed with a plug.
3. It is already waiting for approximately one and a half hours, after which the plug is cleaned and poured 5-7 liters of hot water.

The efficiency of the method with soda and vinegar decreases the stronger than the farthest of the plum is located. You can do without soda, pouring acetic essence and pouring small portions of hot water, but the result will be weaker.

Since almost all chemicals are in their composition of acid and rhythm, it is extremely recommended to work with them without personal protective protection. In order to protect your hands, you should wear rubber gloves, and the eye protection will provide glasses. In addition, you should carefully read the manufacturer's recommendations. Some pipes do not bear the effects of chemistry and begin to collapse. The irregularities formed in this process will lead to the loss of the pipe with a smooth surface of the walls, which guarantees the occurrence of new blocks in this place.

Mechanical methods

Chemicals are well coped with organic sediments, but are practically useless at oppatics, the cause of which is the accumulation of garbage. The most simple mechanical method It is considered to use a vanza. It consists of a cupid or cone-shaped rubber nozzle, which is fixed on a comfortable handle from wood or plastic. The principle of its work is based on crushing of dirt stuck in the sewage.

Cleaning a cloth in the bathroom using a ventuum is less efficient than when using it in a kitchen sink or toilet. This is due to the fact that there is a vacuum to work with it. The plums of the bathroom is equipped with an additional overflow. In the event of a zero inside the air will be located, which will reduce the efficiency of the vehicle.

Nevertheless, it can help at the initial stages of sewage clogging. The actions of actions will be as follows:

1. Tightly closed hole with a bathroom overflow. To do this, use a rubber plug, which should be complete to plum-overflow. If it is not, you can do the cloth folded in a few layers or close it with second vessels.
2. The Bowl of Vanza is tightly pressed against the drain hole so that it completely blocked it.
3. A few (10-20) energetic reciprocating jolts are performed. The nozzle does not have to move away from the walls of the bath.
4. Then a sharp movement is torn to a drain vehicle. Pour water and check the result.
5. If the blockage does not remove, you should repeat the same steps, but with the addition of water. To do this, there are so many fluids in the bath so that the rubber bowl of the canuza is almost completely covered. Vantuz is immersed to the hole, capturing its bowl of water, after which actions are repeated.

To achieve the desired result, you can repeat the procedure several times, but if no improvement does not occur, then further work with the vehicle will not bring the result - the trash sat down too deeply or has a solid structure.

Using a plumbing cable

Vanutuz helps with weak clouds, but the sewage can be scored so much that it will be useless, like chemicals. If a similar situation occurs, you should be aware of how to clear the blockage in the bathroom with a cable. It is represented in the form of a thick wire, at one end of which the lubshik or hook is located, and on the other handle for rotation.

Using this fucking, you need to pull out the garbage to out or pierce it to a wider part of the sewer pipe. Troubleshooting is performed as follows:

• The working tip is placed in the drain hole.
• The cable pushes on the tube rotational movements of the handle.
• If the cable is brought to a block, several sharp jerks are made forward to back, gradually reinforcing pressure.
• Remove the cable inverse circular motions, removing the trash.
• It is served hot water in order to flush the pipe with the removal of fragulated deposits.

The sanitary cable allows you to get rid of blockages that are caused by even a hard garbage in the pipe, such as rags and cellophane films. Its flexibility is enough to overcome all the irregularities and turns of the sewer pipe, even the joints at an angle of 90 degrees. But caution is required to work with it: too vigorous movements can damage the inner walls of the sewer pipe and the drain hole. If desired, the cable can be made independently, having in stock a few flexible meters steel rope. Its end is enough to fluff, giving the shape of the petal.

Further prevention

Understanding the problem of blockage gives an idea of \u200b\u200bwhy the bath clod and how to clean it. But it is better to avoid similar troubles. Protective grilles help to protect sewer pipes. Their main task is the obstacle to the sewage of the hair, animal wool and various garbage.

In addition, several times a month can be poured into a drain hole a small amount of hot water, preferably with salt. It will take fat deposits and rinse them further into the sewer.

For prevention, various helps chemical compounds. Most manufacturers have products to eliminate breaks. There are preparations used to prevent this trouble. They differ in less aggressive components in the composition and, as a rule, can be used for pipes from any materials. It is also necessary to periodically disassemble the siphon in order to clean and get rid of the deposits formed. It is the most effective prevention for the bath, during the operation of which the hair and hair wool are constantly washed off.