Store spinning and other rods are comfortable in a tube. Tubus for rods You can buy, but you can make it yourself. maybe even preferable, because Fisherman can make it specially under his gear, take into account a number of technical subtleties, which will not be in standard shopping tubes. In addition, make tubus for spinning do it yourself - Will not be a lot of work. I'll tell you how it is done.

There is a lot of options to make a tube, but most common - use plastic sewer pipes or air ducts. The tube for rods from such pipes is solid, hard, easy enough. The pipes and fittings for them, the plugs, meanwhile, are very technologically.

So, based on the number of rods and their dimensions, choose a pipe: length and diameter. The length of the pipe should be 5-10 cm more than the length of the rod. The diameter of the tube for the tube should be ± by 5mm more than the maximum dimming of the rod (in the place of the first, largest ring).

In addition to the pipe itself, we will need: plugs for sewage pipes of a suitable diameter, a flat rope (string), a thin polymer foam, fittings, universal glue.

When they cut off the length of the pipe cut along the length, cut off two more rings with a width of 3-4 cm.

And we do in these rings.

In one of the covers we make two slots under the sling. It will be our removable lid.

We take a whole lid. Insert the mug of the foam rubber in it. Sadim this lid on glue. This is a non-removable bottom of the tube.

Rings with slots will serve us to put the strap from the sling. There may be options. Rings are glued to the pipe so that the gap remains where it is possible to skip the sling.

It is best to close the lid and fix the sling through the fastener, such a fittings, like on backpacks.

You can apply an easier way. Make the loop at the end of the sling. Do not stick one edge of the ring and put on it this ring rings. The length of the straps can be changed using special fittings.

There is another option, a more convenient and advanced - a tube with a tissue trim.

Cut the strip of tissue from denim, or other suitable dense tissue.

We coal on the fabric handles from the same slings. You can make a handle for carrying in your hand and put a strap for the toys of the tube over the shoulder.

Buy with good discounts for personal use and as a gift to friends familiar.

Purchase high-quality products by affordable prices in . Make gifts yourself and your loved ones!

Subscribe to us on Facebook, YouTube, VKontakte and Instagram. Stay up to date latest news Site.

How to make a tubus for rods with your own hands?

Spinning, feeders and docks are conveniently transported in solid tubes. They will definitely disappear in them and do not scratch. In fish shops you can buy tubes for one or more rods. Some fishermen make these accessories themselves. Products are much cheaper than reliable and convenient as branded tubes. In this article we learn how to do stubs from plastic water pipes And what are the materials and tools for such work.

Required materials and tools for the manufacture of tube

We will need a pipe plastic plumbing. Depending on the number of rods we select the diameter of the pipe. For example, if you use one or two light spinning on fishing, then you will need a pipe with a diameter of 70 or 90 mm. If you catch a few feeders of the Han or Donski class, it is better to use a 110 mm width tube. Tubes are sold in construction stores:

At home, pretend which diameter of the tube you need and go to the store to buy such pipes. Please note that at the end of the pipe should be thickening. These are us and we need. It is convenient for them later it will wear plugs.

Usually the length of the pipe is 2 meters. We buy a 2-meter segment, two plugs and couplings in a construction or sanitary shop. The coupling looks like:

The plugs will be required here:

From the tools we will need a drill with drills. For carrying a tube, we need a strap with carabins of this type:

It we will be attached to a tube. The strap is better to use adjustable, which changes the length. We will also use two such bolts with some kind of nuts and eyeles:

We will also need glue momentum or another for gluing plastic parts, handbranted metal, marker.

Order of work

First we are determined with a long rod. To do this, we take all the rods that we are going to transport in it and choose from them with the longest knee. We add to it 5 - 8 cm. And we get the length of the tube. After that, we put on one end of the pipe, the plug and the roulette meter the damned distance.

We marke the place where we will cut off the pipe. Usually make upbuses from 110 to 130 cm long. You have a smooth cut, take a roulette and envelope it throughout the pipe diameter. Next, we get a marker on the ribbon and get a flat line. On it and we will cut with a hacksaw.

After trimming the pipe, we should turn out even neck:

It should be well cleaned on the sides and inside so that you can wear a coupling on it. After cleaning, we take the coupling and wear onto the pipe. It should be approached under the diameter of the pipe and dress with effort:

After that, we put on the ends of the pipe plug. One we will put on the glue, and the second will be freely removed and dress. One plug will be the bottom of the tube, and the second is its lid. Before gluing, we clean the inner surface of the pipe and the outer side of the chip of the sandpaper. Thus, we will provide a good clutch of glued surfaces.

Before gluing, fasten the strap. To do this, we will make two holes. In them we will insert two bolts and spin them with nuts. We measure the length of our strap and at such a distance from each other drill the hole drill. We screw the nut from the inside to the bolt. It is important that the hand climbs inside the pipe. The bolt should not be too long to inside about 3 mm. He spoke out of the pipe wall.

This is how the mounting to the bolt pipe looks like:

In the same way, we do the mount at the other end, and the pipe becomes a tube:

It remains to wear a strap and glue one plug. Strap wear in 5 seconds. Just carbines fit him to the ears:

Adjust the strap under your height and wear on your back. Next, we glue the cover to one of the ends and put the product into a dry place on drying.

This species has homemade tubes for rods:

Some fishermen are crushed with hard fabric. This is done more for aesthetic attractiveness than for functionality. The advantages of such tubes in their large operational resource. When falling with a small height, they do not break. They are sealed, do not let the water. The price of such products is somewhat below the shop.

The task was as follows:
I have a free place over the arches of the wheels, as well as many other models of cars, where I laid the fishing rod and spinning, but in the plated covers of the tackle are still subject to breakdowns, so it was decided to get a homemade tube for Storage rods.

The option of the purchase of a shopping tube disappeared due to the size of the distance between the arches (I have 120cm), it's not necessary to pick up for this length, and I didn't want to sacrifice even a centimeter, because There was already a spinning with a transport length of 119.5 cm. Plus almost all ready-made tubes go round shapethat also was not desirable, because He could roll from the arches when moving and maneuvers, therefore disseminated the width of the manufacture of a round sewer tube. Well, the price of more or less decent starts from 1000r and above.

Thinking the Duma, I came across a construction store on the air ventilation channels, which were both round and rectangular cross sectionwhich actually required for my needs

Plastic from which they are made, durable enough, and at the same time not tough, so it will not split from random strikes.
I came up with a size of 120x60mm, which was purchased for the manufacture of a tube with your own hands. But the question arose with end rectangular plugs. They are apparently in nature there is no, looked at the era, and at the Hoklyatsky manufacturer, so I had to take rectangular connectors with valves.

Cut off the piece you need ventilation canal 120 cm long. Connectors cut off the side on one side, almost under the valve. Because It opens freely and closes, fixed it in a closed state and missed glue for plastic window sills (but I think any adhesive is suitable for gluing plastics). As a result, such shamanism turned out end-stubs.

But at the expense of the inner thickness of the plug plugs (which is not bad for the spinning of my size) slightly increased in length, and after calculations and the priking, the air duct itself was cut somewhere on 1 cm.
Inside the plugs made plugs glued pieces of foamed polyethylene (substrate under the laminate) to mitigate and depreciation of possible blows of the tips of the rod.

The plugs themselves are sitting on the box are quite tight, but as reinsurance, with one (deaf) end spinning small self-tapping screws, with false tips, and a little tape was made from another.
Next, it was necessary to come up with a handle. The handle was first taken from packing with blankets, I think, many such packages are available.

Rubber knob itself and flexible connections. In a transitatic state, it practically does not act, which is quite convenient, but by loading the rod into the tubus, I decided to refuse it, having afraid of a certain harness and not the reliability of the design, although there may be a small weight of the gear such an option and suitable.

In the store of sewing and weaving accessories acquired a new handle-rigid and durable. Which was attached to the middle of the tubus.

When mounting the handle, there was a problem, how to spin the screws from the inside of the box with your own hands, the hand until the middle of the tube did not break, and it is not visible where to screw the screws. I solved the problem as follows - I placed the place for the handle on the air duct with two sides, on the one hand drilled holes with a diameter for the screws, on the other side of the hole 1.5-2 times more. And using a thin screwdriver with a magnetic tip, the handle was screwed.

In principle, unnecessary holes were not strongly spoiled appearance. Next you can enclose a tube with a cloth, but I am from this idea
refused, because the smooth plastic is easier to clean and launder than the fabric.

In this homemade convenient tube, I calmly place spinning, feeder and fishing rod, and the tubus itself lies on the wheeled arches, without interfering with loading and unloading things in the trunk, and tackle always with me.

As a result, the costs of the tube were as follows:
-Rorogenous plastic air duct 120x60mm Length 2m. -315r. (But used 1,2m, so it took somewhere 240r)
(According to the catalog, the era is another 1.5 m and 1m, but I needed a piece of home ventilation, so I killed 2 hares at once.)
-For rectangular channel connector with check valve -88p.
-Ruchka -100r.

Total we have about 430r. And a little personal time and strength, but the made of the tube will be exactly the size of which you need, under your rods and the size of the trunk.

There are a variety of tubes for spinning that are sold in stores. However, most fishermen prefer to make a spinning tubing on their own hands. The manufacture of such a tube will not take much time and forces, and in terms of functionality it will not give up counterparts from the stores. Today we consider ways to make an independently given accessory from simple girlfriends.

We measure the size of the spinning, while considering that on each side, 2 cm of foam rubber will be pasted on the plugs. We add 4 minutes for meters. It is suitable for an ordinary plastic pipe, which needs to be noted the length of the gear, and the unnecessary residue should be cut off with hacksaw.

The scaled part will be closed "tightly" plug, the other side will be equipped with a removable lid. After these actions, the Komly Ring is placed in the pipe, which should move freely throughout the length.

At the next stage, we make a cover for the cover and we do several small holes in it to sew a foam rubber. To do this, you can use a sponge. On the final stage Works give the tube of proper species - we are tightened by its cloth.

As a result, the tube will turn out for your spinning, which you will do it yourself, will even better sell analogues.

Required blowing materials

Perhaps you have left unnecessary pipes after repair. If not, this accessory can be found in the construction store. With the search for another suitable material Also, everything is simple, similar profiles that have the necessary stiffness parameter are suitable.

It is also necessary to additionally purchase plugs for plastic pipes. It also takes a foam rubber who prevent damage to the rods inside the case. It is not necessary to buy a whole sheet of foam rubber, a sponge or urine can be used.

The design of the hard case for the rod can be performed different waysWhat we will tell us further.

Cover for Czech

For transportation, rods need a tubus to equip a lid. You can use a thick layer of skin. It is necessary to measure the diameter plastic profile And add 3 mm to it. This size cut the wheel from the skin. A little larger size will not allow the Cride to fall inside the profile. Also cut out a few more similar details of the skin, however, this time they must be 1.5 mm less than the tube diameter.

It remains only to glue with leather parts together. Bottom part The covers will be tight into the plastic tube, and the upper element of the larger will not give her to fall inside. Covers that are made of leather are distinguished by practicality.

Homemade Spinning Case

It will weigh 450 g. The tube made from the profile will last long and will help protect the rods from moisture and various damage. Of all the existing options for covers in the market, homemade is not inferior to them in their parameters.

Options of tube

A homemade spinning tubing will cost inexpensively, as they need materials that are in household:

1. metal-plastic profile;
2. sewer profiles;
3. PVC 50 mm;
4. Ventilation channel and so on.

If these materials are not at home, you can buy them.

Pipe case

Channels of different designs are suitable:

• round;
• square.

The last option is convenient because this design will not roll in the car trunk. Also, the spinning tube, with their own hands differs by practicality. Thanks to him, it is convenient to carry gear.

To start doing a tuba, you need to take care of the presence of the necessary materials.

Make a tube tube

First you need to decide how many fishing rods will be in the case. If several, in this case, select a pipe with a diameter of 110 mm. If the case is needed for one rod, we purchase a pipe from 40, to 60 mm.

The tube is made to fully correspond to the length of the rod. The easiest option of the cover from the pipe is made not several stages:

1. Dimmerly over the entire length of the rod, sprinkle the pipe.
2. Acquire the plug and put them on the design.

All this will be needed less than 20 minutes of time. Pre-plugs are gluable from the inside of the foam rubber, for this you can use PVA glue, superciles or moment. One plug is best glued to the base of the structure.

Necessary materials

Before the start of work, it is necessary to take care of the presence of the following materials:

1. pVC tube (average length up to 2 meters, and diameter from 40, to 110 mm);
2. simple pencil or marker;
3. meter or ruler;
4. a piece of fabric that will be covered with a tube;
5. several pieces of foam rubber;
6. hoven for metal;
7. several plugs;
8. glue.

Blueprints

Before starting work on the assembly of a homemade cover for gear, you need to think about the plan and perform the drawings. Before starting work, it is worth considering how many spinning will be stored in a case, from which material it will be completed and will be covered in the end with a cloth.

In the drawing, all the necessary dimensions of the future design should be indicated, taking into account the length of the rod. In the event that the calculations are not correct, all subsequent work will be not effective, so it is better to check and calculate several times.

PVC pipe 50 mm

To make an option tube for storing one fishing rod, you need to buy sewer pipe diameter 50 mm. It will be perfect option. If we consider the diameter more, then, but is suitable for several spinning.

Required materials Tuba:

1. pipe is 50 mm (it is predefined to measure the desired length, in accordance with the rod parameters);
2. two plugs;
3. tissue for trim;
4. foam;
5. glue.

If desired, one side of the tube can be missed. To do this, pre-apply the adhesive substance on the plug and secure it. Fishing rods must correspond to the size of the tube. When pumping up the pipe, add 2 cm on each side, as the foam rubber will be attached - it is very important.

How to make a cover cover for fishing rod?

You can proceed simply, and purchase a cap on a plastic tube, which will serve as a cover for the cover. If for some reason there is no plug and it is impossible to get it, you can make a lid from the remedies. Cut the circle out of the skin.

The diameter of such a part must be 1.5 mm more than the tube itself. The second circle is cut with this calculation so that its diameter is 1 mm less than the tube. It remains to glue these two elements and dress the cover on the case. For the manufacture of the lid, you can use not only the skin, the felt or other dense material is suitable.

Also worth to attach the cover to one side of the cover, for these purposes, we use the adhesive substance.

Tubs design

You can attach a handle to the cover to be comfortable to wear it, you can also cover it with a cloth or decorate rivets. Categories fantasy and make your cover in accordance with your preferences, and it will attract the attention of other fishermen.

How to cover a tube cloth?

For these purposes, it is better to choose fabrics, which is not too dense by its structure, so it will be much easier to work with it. The stretching and elastic fabric will perfectly sit on a hard case, and if necessary, it can be removed and wrapped.

It is necessary to sew from the elastic material case, which will be a couple of millimeters less than the tube. To do this, pre-prepare the pattern and place it with chalk. The lower part of the cover is stitched with durable threads in a straight line, only then the side seam is performed, which goes perpendicular to the bottom.

You can also equip the case with additional pockets in which you can store bait for fishing. Pockets are sewn over the case itself or the velcro is used, with which they will be attached to the tube itself.

How to make a handle?

If you want to equip your tube tube, in this case it must be attached to the base of the pipe with bolts, it will be more reliable. The handle itself can be purchased at any shopping bags or atelier. If you equip a tube with a handle for carrying, the transportation of the gear will be more comfortable, especially since attaching the handle to the case is easy.

You need to drill a few holes in the pipe under the bolts and fasten the handle itself with the help of them, the length of which is chosen individually.

Store models of tubes

In a fishing store there are several models of fishing covers:

• hard;
• of soft materials;
• semi-rigors;
• tubes.

Economy option is simple soft covers that are made of waterproof fabric. However, the most popular accessory for storing and transporting rods are precisely the tubes. They will not only defend your gear from moisture, but also will be removed from mechanical damage.

Always afraid when loading a car for another departure to break the rods of spinning.

We had to put them on top of all the boosters in the trunk. But their length is 150 cm even in folded form and in the case.

In the end, do not put along into the car (do not fit), across - stick out in the passenger compartment and interfere.

Need a tube ... hard ... and so that you can fix it under the roof of the car on the handles over passenger seats

from the opposite side of the driver's seat.

Ready (commercially available) were not arranged in design and at the price (expensive), I decided to do myself ...

First bought 2. running meters Oxford fabrics, linden, slings ...

Sewer tube with a diameter of 50 only for one spinning.

The diameter of 110 is too big for me (in the presence of only two spins), it will hang in it.

I need a diameter of 70-75, and such a sewer pipe, it turns out that it is problematic to acquire in Russia.

I was looking for a long time and thought to use ???

But ... somehow, going to a hundred to a friend, which is engaged in tinting a brass car, saw a pipe ...

Or rather, the bobbin from the roll roll for tinting. I measured the diameter - it: exactly 70 mm.

I took ... with this moment, these pipes threw each other after using the film.

Now all the materials are and you can start designing ...

The first thing was cut into the size of the pipe a soft plug on the end of the tube.

Inserted and glued ...

And here's the solution - the bottom of plastic bottle From under the kefir, a diameter came up as it is impossible ...

Also inserted a soft gasket.

Now you need to decide on the size of the cutting of the fabric for the cover.

Removed the sizes with a tape measure:

Decaying the fabric on the floor, noted the necessary dimensions:

From the marks cut off.

At the place placed lightning and began to sew ... As a result, it turned out a "stocking", which was subsequently turned out:

Now it is necessary to make fabric caps on the ends of the tube ...

We note on the tissue of the circle, applying the tuba plus 2-3 cm ..

Cut.

After glue superclosure on the ends.

Directly the spinning tube is ready ...

But you need fasteners and belts for carrying.

On the typewriter sew from the lip captures on a tube from the slings, the belt on the shoulder.

As a result, it turned out:

Excellent for driving ...

As well as for attachment in the car:

Passengers do not interfere, but tackle in safety ...

P.S. The article participates in the competition "Self-model".

After reading the article on the manufacture of a "hard" tube for spinning with your own hands,

if it is interesting to you and useful, do not forget to vote for an article ...