How to make a table for a circular saw. A detailed description of making a table for a circular saw with your own hands, which will be useful in any workshop Table for attaching a circular saw

The circular machine is a powerful mechanism that boasts good maneuverability and performance. There are also disadvantages that can be avoided by making the design.

How to make a table for a circular saw

Creating a project plan. You need to measure the space and choose the appropriate size of the structure.
Purchase of materials. In the same step, the required saw is selected.
Step-by-step assembly of the structure. Everything is done according to the drawings made.

Materials and tools

We will need the following materials and tools:

Sheet of particle board or plywood, 20 mm thick.
Tool with disc-blade.
5x5 cm block for creating legs. The cross-section may be smaller if you plan to create a low-power saw.
Varnish or primer.
Solutions for protecting wood from water.
Wood glue.
Self-tapping screws.
Drill and set of drills.
Screwdriver.
Jigsaw.
Machine for milling work.
Clamps.
Tape measure and marker for marking.
Plane.
Sandpaper.

Reference! Also, we must not forget that a circular saw is equipment that runs on electricity. That is, we need a power source into which it will be connected.

Measurements and drawings

The work begins with the creation of design drawings. This step measures the width and length of the table that is being created. The average value is 120 cm wide and 120 cm long. The following materials are ideal for creating the base:

Plywood.
Chipboard.

We are not considering a metal base, since the material is more expensive and the weight of the structure will increase several times. Of all materials, plastic is considered the worst and is not recommended by experts.

Before starting assembly, all wooden elements must be treated with solutions that protect against moisture and rot. After the material has dried, you can begin work.

Attention! It often happens that due to improper installation of the saw, which is installed under the tabletop, the table is overhanging on one side. The blade must be installed in the center of the table.

Important points when working

There are some safety requirements. They will help you avoid injury in the workplace. The requirements are as follows:

DIY table for a circular saw: step by step

The creation process consists of the following stages:

The material must be marked using a tape measure and a marker. We cut the templates with a jigsaw.
Now we mill the edges.
We take sandpaper and process the surface, making it as smooth as possible.
Now you need to turn the tabletop over and mark the place where the saw blade will be installed. This is done as follows: place the tool and trace the sole. We remove the disk. Using a router, we make a hole from 0.5 to 1 cm (depending on the length of the sole).
Now we need to measure the saw and the notch. We mark the clamps and slot locations for the cutting tool.
The next step is to create stiffeners. They are made on the basis of 5x10 cm boards. They need to be positioned so that the distance to the edge of the tabletop is about 10 cm. The smaller side of the board is applied to the tabletop. On one side we make a stroke, and on the other we need to transfer the markings.
Now you need to mark the positions where the screws will be mounted. We drill holes for them. We install fasteners every 100 – 150 mm. We make them relative to the length of the stiffener.
Now you need to mark the longitudinal stiffeners and cut them out. We use glue to fix them, and also tighten them with clamps. After these stiffeners have dried, we install the side ones in a similar way.
Now you need to install the clamps. Self-tapping screws are used for this. The clamps do not need to be removed. We tighten the structure using self-tapping screws around the entire perimeter. We made the holes for them in step 6.
We set the tension for the stiffeners. We use self-tapping screws, the length of which will be greater than the length of those used to fix the ribs. After tightening the tabletop, you can remove the clamps. Now we have a finished tabletop.
The next step is to make the legs. To do this, we take a wooden beam. The legs can be any length, the main thing is that they provide comfort during work. The average distance between the tabletop and the floor is 120 cm, and the length of the legs should be several centimeters shorter.
We cut out the legs and attach them to the tabletop. Their location will be a little off-putting. We fix the bars with bolts (we install them on the outside of the stiffeners).
You can increase the rigidity by making a few additional ties between the legs. For this we use timber.
Now you need to mount the disk plate. We install it inside the hole that we prepared. It is important that the disc fits into the slot without obstructions. We fasten the sole with bolts.
Cover the table with varnish or primer. This will reduce slipping.
Additional elements can be installed. For example, a protective cover, a disc tilt adjuster or a carriage.
If you have minimal knowledge of electronics, you can bypass the start and stop buttons of the saw. These buttons can be installed in a convenient place (most often on the outside of one of the stiffeners).

If you have minimal experience in creating such structures with your own hands, you can easily make a table for a circular stove. The most important thing is to securely fix the saw, regularly check all fastenings, and adhere to safety precautions.

Most people who work professionally with wood would like to have all the necessary machines at their disposal. But unfortunately, this is not always possible. Some people don't have the space to do it, others, and I think the majority, it's money. Any, even the most primitive machine is quite expensive.

But what’s stopping you from just doing it yourself? Nothing is impossible for a person with intelligence. For every carpenter, a circular saw is the main tool. But it happens that only a hand saw is available, and this is not always convenient for large volumes of work. In order not to purchase a separate tool, you can make a stationary mini saw yourself for ease of work - make a sawing table (stand) for it.

Table saw

When choosing a circular saw, you need to be guided by the following characteristics:

Saw power. If the amount of work is quite large, it is advisable to take a tool with a power of at least 1.2 kW.
Cutting depth. The thickness of the material to be processed depends on this parameter. For hand saws it is 40–70 mm. But when installing it in a table there will be a decrease of around 10 mm.
Button placement. The design of the sawing table must provide free and safe access to all control buttons, otherwise it will be necessary to modify the control system yourself.
Rotational speed. For cutting wood, high rotation speed is preferred. This affects the quality of the cut. For plastic, for example, this is not very good. Due to the high rotation speed of the circle, the plastic heats up. You need to choose average characteristics. 3-4 thousand rpm will be enough.

Do-it-yourself table for a circular saw, installation, fastening

To make the saw table itself, you will need to acquire materials that are sold at any hardware store.

We will need:

plywood 15–20 mm thick;
timber 50*50 mm;
boards, approximately 50*100 mm;
switch;
socket;
self-tapping screws;
PVA glue;
rollers;
metal corners.

Making a workbench

Mark and cut a tabletop of the required size from plywood. Clean the surface with sandpaper.
At the bottom of the tabletop we mark places for holes for attaching the saw. To do this, you need to remove the blade and install the saw in the right place, making notes. The holes for the bolts are countersunk on the surface, and the heads of the bolts need to be sanded.
If the material will be cut at different angles, the hole for the disk should be made in the shape of an inverted trapezoid.
Mark the places where the stiffening ribs are attached to the tabletop (from below, at a distance of about 8 cm from the edge). The legs need to be secured to the ribs. The ribs are screwed on with self-tapping screws at intervals of 25 cm and glued with PVA.
The legs are made from timber 100 cm long. Then a screed is made from timber for additional strength.
To be able to adjust the height of the table legs, nuts and M14 bolts are attached from below.
We fix the saw from below.
We attach the socket to the inside of the table. From it we pull the wire to the switch.
We make a parallel emphasis. We cut two strips of plywood, the same length as the width of the table. The width of the stripes is 10 cm. We make the corners round. We sand both strips and fasten them with self-tapping screws. Then we cut two strips of the same length, but three times wider. We fasten them. This will be the guide. We fasten the stop and guide. We set a right angle relative to the disk. We attach the rollers.

Table drawings for a circular saw

There are other ways to make a stand for a hand-held circular saw with your own hands. Here are two more examples.

Table for hand-held circular saw with lifting mechanism

To change the depth of the cut, you can additionally install a lifting mechanism (elevator).

The lifting mechanism itself is mounted from a metal sheet that is attached to the frame on the machine. Lifting will take place along the guides by tightening the bolts.

One way is to install the adjusting rod with fixation nuts. Instead of rods, we use studs. The adjustment handle is made from a plate welded to the end of the stud. At a distance of 4–5 mm from the center we make holes for self-tapping screws. We weld a rod onto the edge of the plate, which we will use to rotate the structure.

Conclusion

From the experience of many people, we can say that although such machines do not look very attractive, with the right and diligent approach, they are no worse than factory ones, such as Interskol, and have no less service life. The big advantage is that the cost of such a machine will be three times lower. In addition, you can make a machine “to suit yourself,” which will greatly increase labor productivity.

A hand-held circular saw is a powerful tool with high performance. One of the main advantages of a circular saw - maneuverability becomes a disadvantage when it is necessary to cut large volumes of wood. To simplify the process, you can easily assemble.

Table structure

The design of a table for a hand-held circular saw is so simple that most craftsmen make it without preliminary drawings and diagrams. This is a sturdy workbench that is made of wood and plywood. The most reliable table bases are made of metal. They are the heaviest and require welding skills. Therefore, stands are often made from waste lumber. A circular saw is attached under the tabletop, the blade protrudes above it through a specially made slot. The lumber is advanced along the tabletop and cut with a rotating disk. For convenience and precision of work, the table is equipped with additional devices: an angular and longitudinal stop.

The tabletop “eats” part of the working surface of the disk, the depth of cut will decrease by the thickness of the tabletop. Therefore, it is advisable to select a circular saw with a maximum disk diameter, and a table top that is thin but hard.

If you haven’t purchased a saw yet, choose models with high power (from 1200 W). They can handle cutting large volumes of wood. Holes will be drilled in the sole for mounting; the cast base may crack. Therefore, it is advisable to choose a tool with a stamped sole.

Selection of materials

To make a good stand for a hand-held circular saw, you should remember your carpentry skills, be patient and have a small amount of materials:

laminated plywood 15 - 20 mm;
timber 50 x 50;
board;
switch;
external socket;
a piece of electrical cable;
PVA glue;
wood varnish (if the plywood is not laminated);
self-tapping screws

And tools:

jigsaw;
screwdriver;
drill;
with a ruler.

The size of the countertop will depend on the size of the workshop. At the same time, it will be inconvenient to saw long pieces on a table that is too small. If the part fits entirely on the working surface, the cut is smoother and more accurate. The height of the legs is selected depending on the height of the master.

For a small workshop, a tabletop design with approximate dimensions of 50 x 50 x 25 cm is convenient.

Table manufacturing process

We cut out a tabletop of the required size from a sheet of laminated plywood. The markings are applied to the lower plane using a metal ruler and pencil. We cut the plywood with a jigsaw, milling the edges if necessary. If the plywood is not laminated, sand the surface of the table.
We turn it over and make markings from the bottom for attaching a manual circular saw. To do this, remove the disc from the tool and place it with the sole in the required place. We make marks on the tabletop and on the sole for fasteners and a groove for the saw blade. Drill holes for the bolts. They will be screwed from above, through the tabletop and held in place with nuts from below. Therefore, we countersink the holes on the working surface side and grind the bolt heads so that they do not protrude.
If you plan to cut material at different angles, the slot for the saw wheel is made in the shape of an inverted trapezoid. For smooth sawing, a regular groove is made. Before cutting the slot and holes for the fasteners, apply a saw, adjust the marks and only then cut.
Mark with a pencil the locations of the stiffeners. They are made from boards and installed from below, 8 - 9 cm from the edge of the tabletop. We will attach the table legs to the ribs. The ribs are fixed with self-tapping screws at intervals of 15 - 25 centimeters, and additionally glued with PVA. Self-tapping screws are screwed in from above, through the tabletop, and the heads are completely recessed. The ribs are fastened together with long self-tapping screws.
The legs of the table are made of a block or board; their length will be from 100 to 113 cm. Legs that diverge slightly downwards will give greater stability. They are fixed with large bolts, tightened from the outside, and secured from the inside with nuts. The timber ties will further strengthen the frame.
To adjust the height of the table, nuts are attached to the bottom into which M14 bolts are screwed.
Now you can fix the saw from below by inserting the disk into the prepared slot.
We attach an electrical outlet to the inside of the table, pass an electric wire from it and install the switch in a convenient place (on the outer part of the stiffener). Power to the outlet will be supplied from the switch. We stretch a wire from it to the nearest power source in the workshop. Using a construction tie, we fix the ON-OFF button on the body of the circular saw in a recessed position.

Let's start making auxiliary stops. For the longitudinal stop you will need #30 square aluminum pipe and two screws with wing nuts.

We saw off a piece of pipe along the length of the tabletop, and cut holes for screws 3 cm from the edge.
We cut out two clamps from pieces of plywood. The structure is ready.
For sawing across the table, we make a plywood sled. We align them with the edges of the table, press them and move them along the toothed circle. We cut a groove where the circle passes through the slide. Small parts can be placed directly inside the slide and sawed.

Dust removal is organized from under the table, but most of the dust flies from above, so it’s a good idea to supplement the device with an upper dust extractor.

Working with a circular saw is very dangerous, so it is important to protect your fingers. Cut out a pusher from a piece of board or furniture panel.

Additions to the design

This design can be supplemented with a riving knife, which will be removed. Put a disk guard on it, which cuts off the flow of chips flying directly at the carpenter.

Some craftsmen, when assembling a table according to unique drawings, completely remove the factory protective casing and replace the factory platform with a homemade one. If you do not plan to cut at an angle, you can remove all the devices for adjusting the tilt of the disk. The saw is fixed directly on the new base, which allows you to gain a few millimeters of cutting depth.

A circular saw is a tool that no home craftsman can do without. This equipment is especially relevant for a country house or cottage. But working with a manual machine is not always convenient, and factory machines are quite expensive.

A way out of this situation may be to make this device yourself. The basis of this machine can be not only a hand-held circular saw, but even an electric drill or grinder.

Making a bed for a circular saw with your own hands is very simple. For production you will need the most regular lumber and quite a bit of time.

Before you think about the design of the upcoming machine, you need to calculate the load to which it will be subjected. The main thing in the bed is reliability and stability. For powerful production saws, the base is a welded reinforced metal structure. But you don’t need such a unit to use it yourself.

If you have just decided to make your own woodworking machine, then you need take into account the main parameters equipment. Since saws can be different, naturally, the design of the bed can also be different.

First of all you need determine the power of the tool. As a rule, for home use, equipment is chosen whose power parameters do not exceed 850 Watts. But, for example, when building a summer house or country house, it is often necessary to saw a very large amount of wood.

That is, more circular power is required. But experienced craftsmen do not advise buying saws where this figure is more than 1250 watts. Installing this equipment in a home workshop is absolutely not justified. And working on it will only increase electricity costs.

The greater the productivity of the machine, the more stable the base it needs. For professional circular saws, as a rule, a base is installed, welded from steel profile. Sometimes these frames are even concreted into the floor. Because vibration of the device can cause danger to life.

Technical features of circular machines

Depth of the proposed cut. The thickness of the material that will be processed on your machine depends on this parameter. This figure in semi-professional and professional machines ranges from 5 to 8 cm. For cutting boards and thick plywood, this is quite enough.

But working with logs on this machine will no longer be convenient. In addition, you need to take into account that this characteristic is reduced in a homemade saw. The depth of the cut will be approximately 1 cm less. But this can be avoided if you provide in the table frame the ability to lower or raise the disk.

When making a tool with your own hands, you need take into account the frequency of its rotation. If you need a circular saw to prepare building materials, then this figure may be less. If a clean and even cut is needed, then the rotation speed is needed quite high. This is needed, for example, for making furniture.

But even in this case, there are certain nuances. This saw is not suitable for cutting plastic materials. Due to very high tool speeds the disk is warming up, and the plastic begins to melt.

Therefore, it is better to choose a device where the rotation speed is no more than 4500 rpm; in this case, the bed for a circular saw can be make from wood. The vibration of this machine is low and additional reinforcement of the table is not required.

Well, in the end, what needs to be considered is the location of the buttons and other controls on your machine. When assembling the saw with your own hands, do not forget that access to the control panel must be safe. This rule is even more important when the open part of the saw is located at the bottom of the tabletop.

In this design, it is best to place the panel with switches from the outside of the machine or make a rising tabletop. This design is also convenient for servicing the device. Then, when you have taken into account all the nuances and little things, you can begin directly assembling the table.

Making a circular saw with your own hands

The simplest version of the frame for a circular saw is a structure made of boards and thick plywood. Moreover, the tool is directly attached to the bottom of the stationary table top. A special slot is made in the table top for the saw.

The dimensions of the table can be changed according to how convenient it is for you to work on it. As an example, an average table is described, the height of which is 110−120 cm. But a lot depends on the height of the person working with the equipment. You can also change the length of the tabletop according to your wishes.

If you plan to work with boards that are longer than 2.6 m, then the cover on the frame will need more. In this case, changes must be made directly to the design and additionally add some supports(legs). Otherwise, the table will create strong vibrations.

For countertops usually plywood is used, which has a thickness of at least 5 cm. But you can also choose plexiglass or fiberglass slabs. But professionals do not recommend using chipboard; this material is not reliable enough.

Tools and materials for assembly

For a circular saw, it is imperative to provide guides. They help cut wood much more accurately. This design welded from angle steel and fixed to the lid with clamps.

It is not advisable to attach stationary guides, since in the future you will not be able to change their position.

To build a table you will need the following materials:

sheet of iron;
plywood sheet;
timber measuring 50×50 mm;
board size 50×100 mm;
steel corner for guides;
two clamps;
hand circular saw.

You also need to first prepare all the tools that will be needed to assemble the table:

Screwdriver, electric drill.
Hacksaw or electric jigsaw.
Tools for measurements (tape measure, square, ruler).
Hand cutter or milling machine.

When everything is prepared, you can begin assembling the table itself. Sometimes craftsmen assemble countertops from unnecessary dining or kitchen tables. But this design is unlikely to last long. Therefore, it is much more reasonable to make all the design elements yourself. In this case, you can also take into account your personal needs.

Making a table top for a circular saw

Assembling the table begins with making the tabletop. The plywood sheet is marked so that the two edges of the lid are the same size as the edges of the iron sheet. Plywood is cut out using a hacksaw or jigsaw.

The edge of the cut can be processed with a milling cutter, but this operation is not necessary. Since the main parameter in the frame is reliability, and not an attractive appearance. The tabletop is rubbed “roughly” with sandpaper.

Mark the bottom of the tabletop slot for circular circle. To do this, you first need to measure the dimensions of the sole of the unit. The easiest way to do this is to unscrew the disk from the device and simply circle the desired part of the saw. These measurements are required to determine the seat.

Using a hand cutter, the bars are selected to a depth of approximately 0.9−1.1 cm. If you do not have a cutter, then this work can be done using a chisel, but it will take much more time.

Then, when the seat is made, try the saw on and, if necessary, adjust the recess. Mark the slot locations for the circle and fixing the fasteners. If you need the circle to rise and fall, then you need install the pendulum mechanism for the countertop.

In this case, the slot must be made in the shape of a truncated pyramid. In this case, the hypothetical top of the pyramid will be directed downward. Directly the frame for the lifting mechanism is best make from steel angles, which are welded to each other.

Making a table frame

The markings for fixing the transverse and longitudinal slats, which serve as stiffening ribs, are best installed on the underside of the tabletop. The planks themselves are made from timber. You will need:

Two transverse parts, length equal to the width of the table top minus 7-9 cm on each side.
Two longitudinal ribs, the size equal to the length of the lid minus 7-9 cm on each side.

Then you need make sockets for self-tapping screws. The slats must be fixed on the lid so that the tabletop extends 7-9 cm beyond the edges of the frame. The fasteners must be as reliable and durable as possible.

The first fastener should be installed approximately 40-50 mm from the edge of the rail. The distance between the screws is approximately 23−25 cm. All details need to drill through. The self-tapping screw is attached to the side of the lid so that its head is completely recessed into the wood.

First, the transverse ribs are secured. In order for the table top to be as strong as possible, the edges of the slats must first be apply wood glue. The structure is fixed with clamps, and without removing them, screws are screwed in.

Allow the tabletop to dry completely. Afterwards, the longitudinal slats are installed in the same way. Then the parts of the frame are pulled together, installing two fasteners on each side. Now the clamps can be removed.

Attaching the legs (supports)

The table legs are made of timber. The height of the supports is selected individually. In practice, it is most convenient to work at the machine when the tabletop located at hip level. Before fastening, each support must be planed so that the leg goes down to an angle from below. So, the area of the base of the support should be slightly larger, in contrast to the area of the top.

It is best to secure the legs using steel corners. They need to be pressed a little so that the base of the machine is in the “spacer”. This gives the table extra durability. Bolts with washers are used as fasteners; they are secured with their heads facing outward. Otherwise, during work you can be injured by the protruding parts of the fasteners.

The whole structure will be more stable if additional supports are tightened with diagonal slats. They are attached in pairs on each side of the machine.

Cover surface polished and varnished or use a steel sheet for coating, which is attached to self-tapping screws. At the very end, the instrument is attached directly to the prepared place.

On the table top you can make additional markings, it will help you cut wood smoothly and correctly. The control panel of the circular saw is located on the outside of the machine. As a rule, it is mounted on one of the table legs. That's all, your DIY circular saw is ready.

If you want to learn how to make a table for a circular saw with your own hands, then read the article.

It talks about the materials that will be needed during the project and the main steps in the process aimed at creating a simple but functional structure.

Materials and tools

A circular saw is a “serious” tool, when using it you must observe safety precautions.

A homemade table, which can be used as a tool stand, will allow you to carry out any manual work with greater accuracy and with less risk of injury.

Before you make a table, you need to spend time carefully planning its design.

It is best to create a detailed drawing containing pre-calculated dimensions of the future “stand”.

The tabletop on which the saw can later be installed should be made of either metal or hardwood. It is better to avoid using resinous wood.

The dimensions of the tabletop should be selected in such a way that they correspond to the planned sawing flow.

It is better to use wooden legs as a base. Plastic, even strong and high-quality, should not be used, since it is not the most reliable material for making a saw table.

In order for the made table to “function” to its full potential, it should be equipped with metal guides capable of moving material under the saw, or rather, under its working blade.

The optimal size of the bed, suitable for most typical sawing work, is one hundred twenty by one hundred twenty centimeters.

If you want to make your table wide and long, then take care of additional supports that will support its structure.

In particular, to give the product stability, it can be equipped with six legs rather than four.

The manual table is assembled using additional materials, including:

wooden beams intended to form the frame of the structure;
fastening dowels;
wood glue;
metal “corners” for attaching legs;
nails and screws.

Tools that may be needed during the work:

tape measure and a rigid construction ruler;
electric jigsaw or hacksaw;
a device having an installed milling tip;
sandpaper (or sanding device);
hammer and plane;
screwdriver (or screwdriver).

Stages of manufacturing a table for a circular saw

Creating a saw table should begin with assembling its frame. To perform this procedure, you can use beams or edged boards, the size of which is fifty by one hundred and fifty millimeters.

The boards need to be knocked together into a single square or rectangular structure, which will serve as both a screed for the frame and a basis for attaching the legs.

The completed frame should be connected to the legs using special metal corners, dowels and screws during the process.

These devices should also be used to connect the assembled frame to the tabletop.

As an alternative, the frame elements can be connected not to each other, but to the legs of the future table. Some carpenters believe that this design is more durable.

The saw must be installed on an inverted bed. Thanks to this, its body and motor will be on the bottom, and the disk, otherwise called the working blade, will be on top.

The hole that allows you to deepen the saw blade into the table should be cut out in advance using a hacksaw or electric jigsaw.

It is important to remember the correct size of the hole, which will reliably “hold” the saw, ensuring the overall integrity of the structure.

Most circular saws have special metal parts that give them stability.

To fix the device on the tabletop, you should make four bars with sawn grooves and drill holes in them for long bolts.

After installing the saw, you should place the prepared bars on its carriage, thereby pressing the device to the bottom of the tabletop.

When attaching the support bars and saw to the tabletop, it is important not to damage the outer part of the bed so as not to create obstacles on its surface for the normal movement of the boards intended for sawing.

Once the saw is securely attached to the table, you need to turn the bed over and screw it to the tie frame.

At this stage of work, you should make sure that all work was carried out correctly and the device is functioning without problems.

Only then can material guides be attached to the table.

Additional Information

Carpentry work requires attention. If you want to make a high-quality and reliable table designed for installing a circular saw, then thoroughly prepare for the process and purchase all the necessary materials and tools.

After assembling the frame, be sure to install it on a flat surface and check that the tabletop of the structure does not overhang it in any direction.

It is better to install the table in the place where it will stand in the future, in order to eliminate possible problems associated with uneven floors.

If, due to an uneven floor, the table vibrates during operation of the saw, then the length of the legs should be adjusted using thick felt or rubber.

The tabletop of the product can be either monolithic or folding. To create a folding saw table, you will have to spend more time and material, and pay special attention to improving the reliability of the frame when disassembled.

The dimensions of the consumables used to create the table are determined experimentally. Ideally, the height of the structure should correlate well with the height of the owner of the saw.

The hole that will be made in the table top must match the dimensions of the specific saw available.

To extend the service life of all materials used, assembled into a single structure, they should be treated with special chemical solutions that can improve the performance characteristics of wood or metal (for example, protect their surface from corrosion, rotting, mold, etc.).

It is better to process wood or metal outdoors rather than indoors, so as not to be poisoned by active fumes.

Inspired by this article, you can make not only a reliable stand for a circular saw, but also a table where you can drink and eat when the whole family gathers.

The technology that underlies the creation of a dining table is in many ways similar to the diagram that can be used to put together a wooden table for a circular saw.

When carrying out work aimed at creating a table for a circular saw, it is important to remember safety precautions.