☰

How to glue the sun-protection film on the window so that it sticks better. Instructions on how to glue various coatings on windows Which side to stick the sun-protection film on the window


Here's how to apply static stained glass film to glass or mirror in detail. Static films adhere to the surface as well as films with an adhesive layer. Please note that in order to securely attach the static film to glass or mirror, this surface must be perfectly smooth. If your glass or mirror has deep engraving or decorative elements, the film may not adhere in these places.

How to stick static stained glass film

1. Prepare necessary tools... You will need: a ruler or tape measure, a pencil, scissors or a utility knife, glass cleaner, a spray bottle or empty glass cleaner bottle, a small piece of soft cloth or a plastic squeegee (a type of spatula used for applying self-adhesive films). The plastic squeegee can be replaced with a discount card with rounded corners or other similar thin and flat object without sharp corners.

2. Measure the surface to be pasted over. Apply the measurement results to reverse side film, and then cut out the desired piece of film. If you are gluing the film to the window, then it is necessary that there is a gap of 2-3 mm between the edges of the film and the glazing bead or window frame. It is not recommended to glue the film close to the window frame. If glued tightly, the film may move away from the glass.

3. Thoroughly clean the glass with a neutral detergent.

4. Dispense regular tap water into a spray bottle or spray bottle. You can use an empty window cleaner bottle. You can add a drop or two of dishwashing liquid for better film gliding, but not required.

5. Spray water liberally onto the surface to be glued. There should be no dry areas.

6. Peel off about a third or half of the protective tape. Place the part of the stained-glass film from which you peeled off the protective film with the smooth side to the glass. It is more convenient to start glueing the film from the top of the glass downward. Begin to smooth the part of the film that is stuck to the glass with a rag, squeegee, or a discount card. The direction of movement for smoothing is from the center to the edges of the fabric. Thus, it is necessary to smooth out the formed small folds and expel water from under the film. If large folds have formed and they are not smoothed out, then the film is crooked. Separate the film from the glass and stick again. Do not press too hard on the film when smoothing to avoid scratching it.

7. Gradually peel off the remaining protective film from the stained glass film and smooth it until the entire piece is on the glass. Then check if there are any creases left. If there are any, then you can lift the edge of the film on this side, lay the film again more evenly and smooth it out.

8. After finishing the application of the film, be sure to remove any wrinkles and remove any water bubbles. If there are some water spots under the film, but they do not bubble, do not try to expel them completely. They will dry themselves within a few hours when room temperature... If the edges of the film lie close to the window frame or go over it, carefully cut off the excess part of the edge of the film using a utility knife and a ruler.

9. After finishing applying the film, do not discard the protective film that you removed from it. Roll this tape and save. Static stained glass films can be used an infinite number of times. If you suddenly need to remove the film, and then reapply it, it is better to store it applied to a protective film. This is necessary so that dust does not collect on the side of the film, with which it is glued to the surface of the glass or mirror.

What to do if, during the storage of the film, it wrinkles and folds have formed, which are not smoothed when the film is applied

In order to smooth out strongly wrinkled areas of the film, it must be heated. When heated, the film becomes elastic. A household hair dryer is fine for heating the film.

Place the film on a flat surface such as a table. You do not need to remove the protective film. Turn on the hair dryer and bring the nozzle of the hair dryer closer to the jammed section of the film. Heat the film to a stretchy state, turn off the hair dryer and smooth out the crease with a soft cloth or by plastic card... If the crease is not flattened or the film is cold and no longer elastic, heat it up again. Do not overheat the film, and do not apply force to the film to avoid stretching it. Repeat this operation for all heavily jammed areas of the film.

Caring for the glued surface

It is recommended to wash the surface covered with static stained glass with neutral detergents or ordinary soapy water.

How to remove static stained glass film from glass or mirror surfaces

It is possible to remove the static stained glass film from the pasted surface without difficulty, regardless of how long it has been in the glued form. To do this, simply pry a corner of the film on either side with a thin, sharp object. For example, the usual kitchen knife... Pull on the piece of film that has come off. The film will peel off easily and leave no residue. Remove all film completely.

Below are videos showing static films from Konrad Hornschuch, a manufacturer of films under the d-c-fix and Alkor brands.

Static Premium Films Application Video

Static Premium - extra thick films for maximum ease of the application process. Also, thanks to the thicker material, the film pattern looks more expressive. Please note that Static Premium films do not have a siliconized liner with centimeter markings. The side with which the film is applied to the glass is covered with a transparent protective film. In this video, before applying the film, a man sprays a very small amount of water on the glass. In this case, in places where there was no water between the film and the glass, stains may form, which will disappear after a while. We recommend that you spray the glass much more abundantly, there should be no dry spots. You can spray not only glass, but also the inner side of the film after removing the protective film.

How water and bubbles are removed from under the Static Premium series films

Removing water from underneath Static Premium films is as easy as shelling pears. With such a thickness of the material, the film does not wrinkle, and the surface of the film is additionally coated with varnish to protect it from scratches. Instead of the demo squeegee, you can use any discount card. The main thing is that the edges of the object you are using for forcing are not too sharp. A sharp-edged item can be wrapped in a cloth or household napkin.

To view the video in a larger size, click on the Yuotube icon in the preview window.

Video demonstrating the application of Static films

The difference between the d-c-fix films of the Static series and the Static Premium series is the lower material thickness. It is the same as for ordinary stained glass films d-c-fix and Alkor with an adhesive layer - 110 microns (the thickness of the films of the Static Premium series is 150 microns). Also, the Static series films have a marked backing. The application process for the Static series is technically the same as for the Static Premium series. Due to the thinner material, care must be taken that the film does not collect in folds, and more thoroughly expel water and bubbles.

When pasting a relatively small area, you may not notice the difference in usability between films with the same pattern of different series. In this case, you should not spend money on a significantly more expensive film of the Static Premium series. When gluing large areas, the difference in the thickness of the material plays a significant role in the convenience of work and the purchase of a more expensive film of the Static Premium series looks justified.

To view the video in a larger size, click on the Yuotube icon in the preview window.

Summer gets hotter every year. This is especially felt in rooms with windows facing the sunny side. The heat problem can be solved by installing air conditioners. However, for those who do not have the funds to buy them, the window film from the sun will be an effective and budget choice.

This article is about window tint film. The publication covers:

  • properties, characteristics of the material;
  • its advantages, disadvantages;
  • instruction how to do it correctly;
  • tips for leaving.

Material characteristics

The sun window foil reflects the sunlight. However, it cannot divert the sun's rays completely, only partially.

The reflective film applied to the windows helps to ensure that the room heats up half as much during the day. It also serves as additional protection. Those who are fond of growing home flowers, glue foil on the windows from the sun to protect the plants from overheating.

How to stick sunscreen film on windows from the sun?

A shiny film on windows from the sun does its job only if it is applied correctly. If you do not follow all the principles of gluing, there will be little sense from it.

Before work, prepare the surface of the windows. On clean glass, the material will fix better, hold out longer and reflect the sun's rays more efficiently.

Glass preparation

Before gluing the film at home, you need to clean the glass with a scraper. To do this, use a model with a rubber tip or another option combined with a sharp metal blade.

The glass is washed with water and diluted shampoo or liquid soap. For half a liter of water, you need about one tablespoon of the product. With a scraper, they clean the stubborn dirt. The main emphasis is placed on the corners and edges of the frame.

More complex cleaning is needed for wood-framed windows. Glazing beads are removed from them, cleaned, and then put back on.

Instructions on how to glue

Not sure how to glue the reflective protective film? To do this, you first need to calculate its exact amount. Each window is pre-measured and a gluing plan is drawn up. The foreman must decide how to do this in a way that keeps costs to a minimum. On each side, you need to leave stocks of three centimeters, which are easily cut off after work.

After cleaning the glasses, the algorithm is as follows:

  1. The roll is rolled out on a flat and clean surface. The required amount of sun-reflecting film is cut off.
  2. Use scissors or a very sharp knife to cut out the desired canvas. If necessary, the evenness of the cut can be monitored with a ruler or tape measure.
  3. The glasses are moistened with soapy water, spraying it from a spray bottle.
  4. The protective layer is removed. To on short term eliminate the effect of glue, we recommend to wet the coating itself strongly with water. This will help to easily stick it, because the material will not firmly stick to the glass. Then the master will eliminate his shortcomings in time.
  5. The upper part of the cut is applied with the adhesive side. Then, gently, slowly, smooth it out to get rid of air bubbles and creases.
  6. Using a rubber spatula, gently smooth the surface, removing the air underneath. If it still remains, raise the closest corner of the film and carefully stick it again, passing over the area with a spatula.
  7. When the film is completely glued, it is again passed with a spatula. This time, the craftsman must remove the excess water. You need to bring it to the edges of the coating.
  8. Leftovers and surpluses are carefully trimmed with a knife or scissors.

Post-application care is just as important as the application of the film itself. She should not be touched with your hands, so that she does not change her position. During the month, you cannot wash the glass, so that it does not lose its protective properties.

After a month, washing is allowed, but there should be no ammonia in the detergents. We do not recommend using hard washcloths that can damage the material.


Tint film is considered to be a film that can be used to paste over windows and other glass surfaces. As a result, the glazed glass receives additional advantages: strength, sound insulation, reflectivity. Window films are a relatively new decoration technique. However, its functionality has already been appreciated not only by professionals, but also by ordinary consumers. Observing the technology, such a film can be easily glued by yourself.

Varieties of films

Today on the construction market there are about 100 different modifications of the tint film. It is divided into several types: protective, mirror, sunscreen or reflective, energy-saving and matte.

Protective films provide additional strength to the glass, they are transparent and tinted. Fragile surfaces covered with foil acquire good shock-resistant properties. If the glass breaks, the fragments will not fly apart, which completely eliminates injury.

Tinting with a mirror film looks very impressive on glass. Windows receive an additional reflective effect, creating one-way visibility. The surface of the film will protect the interior from the scorching rays of the sun and prevent paint fading.

The direct purpose of the sunscreen film is to protect the premises from excess sunlight... The glass gets light reflectivity and extra strength.

Energy saving films have a multilayer structure. They keep warm indoors well in winter and additionally provide coolness in summer. At the same time, electricity is significantly saved. You can skip the heaters in winter frosts, use less air conditioning in the summer heat.

The matte film is available in one color and with a pattern. Possesses decorative functions. It additionally enhances the strength of the glass and protects the interior from the scorching rays of the sun.

We glue the film ourselves

You can glue the film on double-glazed windows and windows in wooden frames. The service life of the coating depends on adherence to the technology when gluing. As a result, the surface should be completely flat and smooth, without bubbles or voids. It is recommended to tint the glass before installing the glass unit. It is more difficult to stick the film on the built-in windows. The process will require some experience and skill. With wooden frames it is easier - just remove the windows, remove the glazing beads, stick on the film, nail the glazing beads and reinstall the windows.

To tint windows yourself, you need a tool:

1. Tinting film purchased at any hardware store.
2. Janitor with a strip of rubber along the edge. It will allow you to thoroughly smooth the surface of the film.
3. Water spray gun.
4. Painting knife with sharp blades.
5. Special scraper for scraping off dirt.
6. Liquid soap or shampoo, cotton rags.

During the installation of the film, it is desirable that the temperature regime of the environment fluctuates from +7 to + 40 ° C, the humidity is - 20-80%. The lowered temperature will prevent the adhesive layer from drying out quickly and gaining strength. If the temperature is high, then the film, on the contrary, will dry out too quickly. If the humidity is high, the adhesive surface dries slowly, the bond strength decreases. When the weather is hot and the humidity is low, the pasted film dries faster.

Before pasting the glass with foil, be sure to wet cleaning premises. Dirt and dust particles will deteriorate the quality of the coating, leading to the formation of bubbles. During the gluing process, you can additionally spray the room with water to minimize the amount of dust. Strictly adhere to the rule: remove the protective layer - immediately stick it on. Otherwise, static electricity will instantly attract lint and dust to the exposed adhesive surface.

Preliminary preparation of glass

Before pasting, wash the glass thoroughly with soapy water. Do not use alkaline detergents. If not washed off, the adhesive base of the film may dissolve as a result. Moisten the window surface liberally. Scrape off the adhering dirt from the glass with a scraper, wipe dry, especially in the corners and along the rubber seals.

Cut the foil before gluing

Measure the surface of the pasting, note down the dimensions. Cut the film according to the markings, leaving an allowance on the sides of 2-3 cm. It is better to cut off the excess later than not guessing the size when cutting. If the film is narrower than the glass, then the joints of the sheets should coincide with each other when gluing. Preferably the factory cut side.

Surface gluing

In water, dissolve an alkaline liquid soap or shampoo, in the ratio: 1 tbsp. spoon per liter of water. On the cut pieces of the film, you need to stick strips of adhesive tape around the corners. They must connect the decorative and protective layers of the film. Then separate the strips of adhesive tape, while the protective layer is easily removed by sticking to one half of the tape.

While removing the protective layer, abundantly spray the adhesive surface of the film and glass. Make sure that the areas of the film do not stick together with an adhesive layer. You cannot separate them. Periodically moisten the adhesive surface of the film and the washed glass with plenty of water. Place the adhesive side of the film on the glass, gently holding the edges. Smooth with a spatula from the center to the sides, carefully removing air bubbles and water droplets.

The final stage

After gluing, cut off the extra centimeters with a clerical knife. Then, go around the edges and corners again with a spatula, removing air bubbles and remaining water. Moisten the spatula periodically so that the surface of the film is not scratched. While the film is wet, you can slightly tweak it and move it. After distillation, it will be impossible to fix anything. Carefully walk along the edges of the glued film to avoid peeling.

After the final leveling of the surface, the glass unit is ready for assembly. If the frames are wooden, we stuff the glazing beads, preventing the film from tightening. If possible, do not reassemble window frames until the adhesive layer is completely dry. This usually takes about a week. The higher the air temperature, the faster the film will dry. After drying, it is better not to touch the surface during the day, let it "grab" well. It is better to wash tinted glass with soapy water, without using abrasive powders. They can scratch and ruin the finish.

September 19, 2016
Specialization: Master in Construction plasterboard structures, finishing works and styling floor coverings... Installation of door and window blocks, decoration of facades, installation of electrical, plumbing and heating - I can give detailed advice on all types of work.

If you are faced with a problem with protecting the premises from the summer heat and you need to solve it with minimal cost, then a great solution foil can become, and you can use different versions of it. I will tell you about what you can find on sale today and how to carry out the work in order to protect yourself from the sun and not spoil the window.

The main product options and their features

Foil for windows from the sun can be different, I will talk about the options that are most common. We will figure out how to fix them better, what are the pros and cons of this or that solution, and in what situations it is better to use a certain type of product.

Option 1 - regular foil

This solution has several undoubted advantages:

Affordable price In what, but in cost, this option has no equal, the baking foil has affordable price... If you need to solve the problem with heat at minimal cost, then this method simply cannot be found better.
Availability You can buy material both in hardware and grocery stores, which have a small section with little things useful for housewives. Roughly speaking, you can go out for bread and buy everything you need to build a sun protection system.
Efficiency The surface of the foil reflects the sun's rays very well, thereby allowing a noticeable decrease in the temperature in the room without the use of special equipment
Ease of use Not needed for work special tool and fixtures, fastening is done very quickly and very simply, below we will analyze this process in detail

Naturally, this option has its drawbacks:

  • The biggest drawback is that aluminium foil opaque, so if you glue the windows completely over it, then the room will be dark. Alternatively, you can close the window opening only partially, this will reduce the efficiency, but it will provide the room with at least some natural light;
  • Another disadvantage is not very attractive appearance. Of course, if you need to quickly solve a problem, and the view is unimportant, you can ignore this aspect, but still many people want the window to look more or less dignified;

  • If you do not know how to glue the foil to the window and listen to the advice of pseudo-masters, then it is very easy to spoil the surface. Improper fastening makes the process of removing the foil very long and tedious, you will have to sit by the window for more than one hour.

Let's figure out how the installation is carried out. I previously read the information on this issue on the Internet and do you know what I found? That the request "how to remove the foil from the window" is much more common than the question of how to glue it.

The fact is that many fix the foil as tint - they apply a soap solution to the glass, apply the material and expel moisture from under it. As a result, when it is necessary to remove the protection, it is found that the foil is torn off in small pieces and there is another way out than to pore over a window with a blade or construction knife simply no.

I will tell about more easy way, it may be less attractive, but it takes a little time, and it will not be difficult to remove the foil later.

Before gluing the material to the glass, you need to stock up on everything you need, the list is very simple:

  • Foil in the required quantity, to determine how much it is needed, measure the area of ​​the glass, then on the spot you will be able to orient yourself based on the width and length of the rolls;
  • Scotch tape - the most common option will do, but you can use a narrow one, work with it will be a little more difficult, but removal will be much easier;
  • Scissors are needed for cutting materials during work.

The work is done like this:

  • First, the window is wiped so that there is no dust on the glass and frame, which will allow the adhesive tape to stick much more reliably;
  • Next, you need to take measurements to determine which pieces the foil will be cut into. For work, it is better to adapt either a large table or free up the floor space, since the material is very fragile and can be easily damaged;
  • The cut piece of foil is placed on the surface, after which you need to glue a piece of adhesive tape to the upper side so that it half enters the material;
  • Next, the element is fixed on the window, it is better to glue it to the frame, but you can also directly on the glass, it all depends on the situation;

It is better to glue the foil strips together already on the window, and not on the floor, or, it will be much easier this way.

  • And do not forget that the material is opaque, so before you glue certain areas, you need to decide which part of the structure you will leave open. Try to choose the area where the sun shines the least.

A little advice on removal - after peeling off the tape, traces may remain, which is easiest to wipe off with a window cleaner.

Option 2 - curtain film for windows

It's over reliable view products that are specifically designed for use in window structures. The sun-protection film-curtain has a number of important advantages:

  • Strength - this material is much more reliable than brittle foil, therefore it is easier to work with it, you will not be afraid to damage the surface with one careless movement;

  • Convenient dimensions - the products are sold in rolls 60-100 cm wide and 3 m long, this configuration is well suited for window structures;
  • Affordable cost - one roll will cost you only 100 rubles, and this, with quality, is many times better than that of plain foil;
  • Attractiveness - if you carry out the installation in accordance with all the recommendations, then your windows will look very neat and even presentable;
  • Transparency - the film reflects light from the outside, but from the inside almost does not limit the view, only slightly darkens the glass. Thanks to this, you can safely cover the entire area and provide the most effective protection from the summer sun.

  • There are two product options, each with its own advantages. One option is glued to the glass, and the second is used as a curtain, each has its own advantages, and you can choose a specific solution.

Do not buy Agrokhoztorg products, as this is the most unreliable option on the market. The packaging says "Beware of counterfeits", but the original does not differ in quality - there are cases when the material fell into disrepair the next day after gluing, and it was almost impossible to tear it off.

Now let's figure out how to carry out the work with our own hands, I will begin consideration with more simple option, which is called "sun blinds" and may have different sizes... The workflow with this type of product is extremely simple:

  • Before you stick the curtain, you need to wipe it upper part frames, the material will attach much better to a clean surface;
  • Next, you need to unfold the canvas, make sure that it fits, then remove the protective film from the upper adhesive strip and press it tightly against the frame, this completes the installation.

The film transmits light and can be moved as a curtain if necessary, which is very convenient.

Now let's deal with the option that is glued to the glass, here the instructions for carrying out the work are more complicated:

  • First you need to wash the window very well, if there are any specks or stains on it, then the film will only emphasize them and spoil the entire appearance of the window opening. For washing, use any means, the main thing is that the surface is clean;
  • Then measurements are taken to determine the dimensions of our glazed areas. After that, you need to cut out the material, but not exactly in terms of parameters, but with a margin of 5 mm in all directions, this will eliminate the waste when there is a gap around the perimeter, and will simplify your work, because slight distortions are easily compensated by the stock of material;
  • The surface should be abundantly moistened with soapy water, this will avoid immediate adhesion of the film to the glass and will help to adjust its position. For work, the easiest way is to use a spray gun so as not to flood the entire window structure;

  • The protective layer is also removed from the reflective material and the same soap solution is applied to the surface. You shouldn't have any questions about which side to glue the material on - the reflective surface always looks outward, it is this surface that should be very abundantly moistened;
  • The prepared element is neatly positioned on the glass, thanks to the soapy solution, the film moves well along the base, and you need to align it in an optimal position. There should be no large folds on the surface;

  • Moisture from under the film is expelled either with a regular rag, or with a rubber spatula, if one is at hand. Work is done from the center to the edges, make sure that moisture does not remain anywhere;
  • Lastly, the blade cuts off the excess material around the perimeter, after which you can enjoy the result of the work.

The use of tint film for windows is inexpensive, but maximum effective method protection against solar radiation. Such material is able to delay up to 99% ultraviolet... Moreover, the tint film for windows is capable of minimizing the level of infrared radiation by up to 80%. These indicators are quite enough to avoid possible overheating of the room in hot weather.

In the manufacture of tint films, they resort to the use of polyester, which significantly improves the strength and elastic characteristics of the material. It also improves the light transmittance of the film. Such material is extremely environmentally friendly. It is non-toxic and completely non-flammable.

The unique technology of film production allows minimizing the amount of incoming solar energy without significant loss of optical visibility. In most cases the material consists of several layers... Some variations of this type of product may contain a combination of a colored layer laminated with a film. From above, the coating is presented in the form of a finely dispersed metallized layer. Due to this, the colored layers located below are not subject to rapid fading.

The metallized layer acts as a kind of shield for solar radiation. As a result, one can expect an improvement in the protective properties of the film.

Important: In winter time such a coating allows to reduce the level of heat loss due to partial shielding of thermal radiation inside the room.

The expediency of using a tint film on windows is determined by the subsequent increase in the impact resistance of glass. Such material has no negative effect on growth. indoor plants... The latter quickly adapt to the new mode of absorption of ultraviolet rays.

Types of tint films for windows

Today, manufacturers offer a fairly wide range of products of this type. Each of the presented variations has characteristics that define the individuality of the film. The multilayer structure of the material provides high-quality protection against ultraviolet and infrared radiation.

During the production process, they can resort to the implementation of spraying with aluminum, titanium, bronze or nickel. In some cases, silver or gold can even be used for this. The connection of individual layers is carried out using a special device called a laminator.

1. Sunscreen film

Such a film is able to trap up to 99% of the sun's rays. It is most advisable to use this coating in offices or study rooms, where it becomes necessary to create appropriate conditions for working with a computer or important papers. The film on the windows from the sun protects individual elements of the interior from fading, and also reduces the level of load on the air conditioner - in the summer it allows you to additionally cool the room, and in winter it prevents hypothermia.

2. Mirror film

This material has a mirror effect. This variation of the film has the properties of filtering infrared radiation and sunlight. The implementation of such a coating avoids fogging of the windows. The mirror layer can be located on the inside or outside of the glass.


3. Protective film (shockproof)

In addition to performing its direct functions, such a film is additionally capable of protect glass from direct mechanical impact... Its presence allows you to avoid the appearance of fragments in case of damage to the window. There are some variations of films that are able to minimize Negative consequences explosion. They are most often used in crowded places. In residential premises, a fireproof protective film can also be used, which is able to delay the spread of smoke and fire for a short time.


The decorative film can have different color scheme... A large number of shades allows you to solve design problems of various levels of complexity. There is a decorative film with a graphic design. The surface of such material can be matte or transparent.


5. Architectural film

Another type of window tint film that can be used to solve design problems. Most often, it is used during the design of building facades. The architectural film is glued to the outside of the glass. Additionally, it provides increased strength and protects against direct mechanical stress.

And you can, on the contrary, use the sun to your advantage and Details are here.

Color gamut width

Balcony and loggia tinting, or other room in the house, can be done when using various variations material. When resolving this issue you can choose a film that meets the required color requirements. A wide palette of colors allows you to achieve the desired result without any problems.

The transparency level of solar control films for windows can vary from 15% to 35%. With the use of a silver coating, this figure can reach 50%. It should also be noted here that the classic silver mirror film can be realized from the outside of the glass.


Features of gluing

While doing installation works certain nuances should be taken into account. In this case, the resolution of this problem will not be fraught with significant difficulties. It is necessary to focus on the need to comply with a certain temperature regime... When gluing the tint film in the room, the temperature must be kept from +5 to +40 degrees.

It is also very important to control the humidity level in the room. This indicator should not exceed 80% and be below 20%... Moreover, when performing installation work, it is recommended to resort to the use of a sprayer as often as possible, which creates the necessary humid environment in the immediate place of gluing.


On preparatory stage should be carefully get rid of dust on the glass surface... The film must also be free of foreign particles. Otherwise, the quality of the toning will be too low, as a result of which there will be a need to repeat the work.

Please note: When removing the protective layer from the window tinting film, it is very important to ensure that no dirt or dust particles get onto the surface. In a different scenario, the final result of the work done will be unsatisfactory.

Before gluing the tint film, you must carefully wash the glass with detergent, which should not contain a large number of abrasive substances. It is recommended to use a scraper to clean up traces of dirt.

Tinting of windows, including balconies and loggias, can be carried out from the inside or outside of the glass. To minimize the negative impact of weather conditions, work should be carried out from the inside.

Required tools

To minimize the amount of time required to perform glass tinting work, you should choose the correct the right tools... An approximate list of equipment will look like this:

  • stationery knife;
  • spray;
  • putty knife;
  • paper towel;
  • detergent.

The trowel width should be as large as possible, and the used detergent shouldn't be aggressive. It is best to use liquid soap or baby shampoo. The feasibility of using a paper towel is determined by the fact that it does not leave lint on the surface.

Sequencing

Compliance with the technology of work allows you to count on a positive final result. Before tinted windows on the balcony, it is recommended to adhere to a certain sequence of actions, which in this case will look like this:

  1. Glass preparation.
  2. Film preparation.
  3. Moistening the glass surface.
  4. Removing the protective layer of the film.
  5. Fixing the film on the window.
  6. Displacement of water with a spatula.

Tip: To prevent the spatula from damaging the surface of the film, it is recommended to resort to using a rubber or plastic variation of the tool and pre-wet it.

It may take about a week for the film to dry. As excess moisture is removed, the coating will gradually lighten. Air bubbles formed on the surface during installation will disappear as it dries.

Care features

Window tint film requires special care. So, it is not recommended to use products containing abrasive additives to wash it. Wipe the surface with warm water and soap, using a microfiber cloth. Provided that a sponge is used, given element should not contain too large pores, into which dirt can clog.

Balcony tinting: video

We invite you to watch a video on the topic of our article and watch the tinting process on the balcony.